Uno r3 usb

Microcontroller:ATmega328 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 150 mA Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader 2 KB (ATmega328) 1 KB (ATmega328)

DESCRIPTION Operating Voltage: 5 V USB Controller: MAX3421E Max Current: 500mA when Arduino is powered by a suitable power supply connected to the Arduino power jack Max Current USB: 400mA when Arduino is powered by its USB port Features: The following device classes are currently supported by the shield: 1) HID devices, such as keyboards, mice, joysticks, etc.2) Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Arduino Mega only) USB 2.0 Full Speed compatible 3.3/5V operation level compatible All GPIOx pins break-out USB Host 5V/500mA supply for USB protocol Works with standard (dual 5/3.3V) and 3.3V-only (for example, Arduino Pro) boards. Mention that you found this ad on DealMarkaz.pk when you call.

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com USB Host Shield 2.0 Description: The board’s improved layout makes this shield compatible with more Arduinos, makes it easier to use and opens new possibilities. The main differences from rev.1xx are outlined below: The SPI interface has been moved to ICSP header making shield compatible out of the box with “big” Arduinos – Mega and 2560. Standard size boards, such as Duemilanove, UNO, as well as clones with classic connector layout, are also compatible with this revision of the shield. This compatibility is maintained on a software level as well – all necessary code changes are performed using conditional compilation preprocessor directives.

The Uno is a microcontroller board based on the ATMega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.. You can tinker with your UNO without worrying too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again........... Shop now from http://www.w11stop.com/embedded-boards/arduino/arduino-uno

ARDUINO EDUCATION STARTER KIT we also deals in variety of ARDUINO BOARDS with rock bottom price Specificatoin Arduino Education Starter Kit Specification: ARDUINO UNO R3 board * 1 High quality and large bread board * 1 RFID module * 1 IC Keychain * 1 Non-contact type IC card * 1 I2C 1602 LCD module * 1 5V Relay * 1 DS1302 clock module * 1 Voice detection module, * 1 Temperature and humidity module * 1 Level detection module, * 1 4 * 4 keypad module * 1 Three-color RGB module * 1 XY joystick * 1 Servo * 1 Stepper motor driver board * 1 Blue LED * 5 Yellow LED * 5 Red LED * 5 1k resistor * 5 10k ohm resistor * 5 220 ohm resistor * 8 Buzzer * 2 Key module (with hat) * 4 ROCKER SWITCH * 2 LM35 sensor module * 1 Photoresistor * 3 Fire * 1 Infrared receiver * 1 Adjustable potentiometer * 1 A digital control * 1 4 digital tube * 1 8 * 8 dot matrix module * 1 74HC595N chips * 1 Infrared remote control * 1 Breadboard Jumper 30 Male to Female DuPont lines * 30 9 volt battery snap * 1 USB Cable * 1 Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com