Tune tuning auto

EFI Auto Car Theory + Practical Training Course in Rawat Sahiwal . New session of EFI Auto Car electrician course will be started soon in international college of technical education. Admission are open in international college of technical education for both boys and girls 923115193625. Best institute for EFi Auto Electrician course in Rawalpindi pakistan.The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.call 03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com. EFI Auto Car Theory + Practical Training Course in Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. International college of technical education offers different type of courses and diplomas out of which some are as follows:

New session of EFI Auto Electrician course will be started soon in international college of technical education. Admissiona are open 03115193625. ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Auto electricians or automotive electricians concentrate on the electrical parts in motor vehicles.Their job descriptions entail installing, repairing, wiring, and maintaining of all electrical components found in different vehicles.They also check what is necessary to bring automobiles up to their best working condition.They may also treat equipment used in agriculture and mining such as excavators and tractors.Those in this line of work have to be technically knowledgeable in the use of equipment and machinery to do the job.They have to be familiar with how wires work and how they have to be placed in a vehicle.They also need to know the type of wiring techniques to utilize for the various components they work with.They must be good at testing equipment and the computers they use in mapping out electrical pathways and locating electronic problems or malfunctions in the system. They have to be able to dissemble, as well as correctly reassemble vehicle parts back together. They must be able to understand the equipment installed in each unit. They need to make sure the equipment is fully functional and clean, as well as making sure it is connected to the automobile’s main power source. Auto electricians also use meters and circuit diagrams to search for faulty parts of vehicles. EFIAuto Electrician Diploma Course in Rawalpindi Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, he design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7″ Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualifie staff.call03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com.Pakistan.Basic IT Course (MS Office) Computer Hardware Course Computerized Accounting CIT (Certificate in information Technology) Web & Graphic Designing Computer languages Software Engineering AutoCAD (Civil, Mechanical, Electrical) 3D Studio Max (Advanced) Computer Networking Web Development Information Technology (PG-DIT) Project Managment Professional (PMP) Prima Vera (Project Management) DIT (Diploma in information technology) Revit 3D Cad Course Micro station Cad Course Shorthand Professional Course in Islamabad Shorthand Professional Course in Rawalpindi Shorthand Professional Course in Pakistan.Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management Diploma in Guest House Management Diploma in International Tourism Management Diploma in Energy Management Diploma in Library Management Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management Diploma in Interior Designing Diploma in BMS (Building Management System) Hospitality Management Course in rawalpindi Hospitality Management Course in lahore Hospitality Management Course in peshawar Building Management System (BMS) Course in rawalpindi Building Management System (BMS) Course in lahore Building Management System (BMS) Course in peshawar Quality Assurance Quality Control Course in rawalpindi Quality Assurance Quality Control Course in lahore Quality Assurance Quality Control Course in peshawar Hotel Management Course in rawalpindi Hotel Management Course in lahore Hotel Management Course in peshawar Iosh MS OSHA 30 USA Safety Course IADC Rig Pass Icertosh (International Certificate in Occupational Safety and Health)Safety Officer IRCA, ISO Certifications Nebosh IGC Course in Rawalpindi Nebosh IGC Course in islamabad Nebosh IGC Course in peshawar Nebosh IGC Course in karachi Nebosh IGC Course in lahore Nebosh IGC Course in pakistan Basic IT Course (MS Office) Computer Hardware Course Computerized Accounting CIT (Certificate in information Technology)

EFI Auto Car Electrician Course In Sahiwal Sargodha.ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625. International college of technical education is best institute which offers The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan. EFI Auto Car Electrician Course In Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Visit our webistes for further details of this course www.icollegete.com,www.courses.com.pk

EFI Auto Electrician Course In Chakwal Sahiwal . ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625. The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi Pakistan. EFI Auto Electrician Course In Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Visit our website for further details of this course www.icollegete.com,www.courses.com.pk

EFI Auto Car Electrician Course In Bannu Kahuta . Best EFI Auto Electrician Course offered by international college of technical education. High Quality assistance provided by international college of technical education to students.ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625.The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operation Engine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing. Visit our website for further details of this course www.icollegete.com,www.courses.com.pk. International college of technical education offers different type of courses and diplomas out of which some are as follows: Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management Diploma in Interior Designing Diploma in BMS (Building Management System) Hospitality Management Course in rawalpindi Hospitality Management Course in lahore Hospitality Management Course in peshawar Building Management System (BMS) Course in rawalpindi Building Management System (BMS) Course in lahore Building Management System (BMS) Course in peshawar Quality Assurance Quality Control Course in rawalpindi Quality Assurance Quality Control Course in lahore Quality Assurance Quality Control Course in peshawar Hotel Management Course in rawalpindi

EFI Auto car Electrician course in Attock Jhelum . International college of technical education is best institute which offers national and international courses and diplomas which are acceptable in international countries as well as in domestic country.Admission are open in international college of technical education 923115193625. The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.call 03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com. International college of technical education offers different type of courses out of which some are as follows: Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management

Efi Car Auto Electrician Course in Faisalabad Sialkot, Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia, International College Of Technical Education Offer Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia 03115193625, Best Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia 03354176949, Professional Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia 03115193625, Lowest Fee Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia 03354176949, Admission open for boys and girls International College Of Technical Education certification acceptable in Government job and Worldwide UK USA KSA Canada Japan China Saudia Dubai Muscat Oman Bahrain Kuwait Qatar, Practical work Efi Car Auto Electrician Course in Rawalpindi Taxila Wah Saudia, An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to controll engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of "electronic control unit", and then specific ECU's were developed. Now, ECU's are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU's and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle.Car Electrician EFI Electrician course in Rawalpinidi, Islamabad, Pakistan. Auto Electrician Course in Rawalpindi, Islamabad, Pakistan. Auto EFI Electrician course in Rawalpindi, Islamabad, Pakistan. EFI Car Electrician diploma course in Rawalpindi, Islamabad, Pakistan. Auto Electrician course in Islamabad, Rawalpindi, Pakistan. Car Electrician Course in Rawalpindi, Islamabad, Pakistan.Diploma in EFI Auto Electrician course according to the requirements of market demand on international standards. Our professional Trainers train students in all fields of Auto Electrician and EFI Technology. After the completion of Diploma in EFI Auto Electrician course students can do job as auto electrician and EFI technician in local market and abroad, also can start their own business with full confidence. Our trainers help them in job placement and also provide assistance to start business. Introduction to EFI Engine system Tools use in EFI system Precautions of working environment of EFI system Difference between Distributor and CDI EFI engine check light system The purpose of Check Engine Light EFI Engine Sensors working operation system Cranking and Cam sensors degree notification in EFI System What is Air Bag system how its work How working of EFI engine fuel injector and its plus Difference between Throttle and carburetor system ABS Breaking System in EFI system EFI Engine Manual Diagnostic System EFI Engine Tuning System Catalytic Convert system in EFI How to control ECU EFI Engine Automatic and Manual Gear system EFI Fuel Pump system Cranking and charging systems

Efi Auto Electrician Course in Chakwal Jhelum Dubai, Efi Auto Electrician Course in Muzaffarabad Bagh Saudia, International College Of Technical Education Offer Efi Auto Electrician Course in Muzaffarabad Bagh Saudia 03115193625, Best Efi Auto Electrician Course in Muzaffarabad Bagh Saudia 03354176949, Lowest Fee Efi Auto Electrician Course in Muzaffarabad Bagh Saudia 03115193625, Admission open for admission and queries call 03115193625,03354176949. INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training, Technical, Management and Safety Officer Institute, For More Information Visit Our Website http://www.icollegete.com/ https://courses.com.pk/ Certification acceptable in Government job and Worldwide UK USA KSA UAE Canada Dubai Muscat Oman Bahrain Kuwait Qatar Saudia Japan China, Efi Auto Electrician Advance Professional Course in Rawalpindi Muzaffarabad Bagh Saudia 2021, EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment. Automotive electricians often interact directly with a customer asking for clarification of the problem with their vehicle, and then explaining what needs to be done.EFI Auto Electrician Course In Rawalpindi, Pakistan Auto Electrician is there to service, maintain, check up, repair, and change electric and electronic devices and systems on the vehicle. A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions.Also, this tradesman should perform quality control for the electrical work performed, considering the norms and regulations.Within the auto electric trade courses, International College of Technical Education has a six-month auto electrician course to offer. Having finished this course, each student will be able to identify the types and elements of electric installations, and network equipment; to differ the electric symbols, and explain how the electric installations are set up on a vehicle.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.The auto electrician course in International College of Technical Education offers you the chance to learn about terms such as ECU, and CPU, learn what system sensors are, and explain how they work (coolant fluid temperature sensor, air temperature and flow sensor).In our school you will learn what an encoder is, how it functions, what is Hall effect, what is a “Knock” sensor, and what is the purpose of the sensor for the car speed.This training for auto electrician is the best and the most comprehensive possible offer.It is a reliable and high-quality course to prepare you for this trade, highly in demand.The practice within this training is certainly the most important segment. You can have the practice in a shop that ICTE Institute cooperates with, and it is not included in the course fee. Within the course fee we have included the textbook, the final exams, and a certified diploma. EFI Auto Electrician Course Contents: 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Admission open for admission and queries call 03115193625,03354176949. INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training, Technical, Management and Safety Officer Institute, For More Information Visit Our Website http://www.icollegete.com/ https://courses.com.pk/ Certification acceptable in Government job and Worldwide UK USA KSA UAE Canada Dubai Muscat Oman Bahrain Kuwait Qatar Saudia Japan China http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi-pakistan/ http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi-pakistan/ http://www.icollegete.com/course/electronic-fuel-injection-efi-course-in-pakistan/ http://www.icollegete.com/course/auto-mechanical-course-in-rawalpindi/ http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi/ http://www.icollegete.com/course/competency-experience-based-diploma-course-in-rawalpindi-pakistan/ http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/ Efi Auto Electrician Course in Muzaffarabad Bagh Saudia

EFI AUTO ELECTRICIAN course in baag muzaffarabadInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment EFI Auto Electrician Course Contents: Tools Special purpose tools Measuring Instruments Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Batteries This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI VEHICLE AUTO ELECTRICIAN course in Abbottabad HaripurInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment his course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI VEHICLE AUTO ELECTRICIAN course in Mardan Charsadda RawalakotInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment his course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI AUTO ELECTRICIAN course in HANGU KARAK International college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment EFI Auto Electrician Course Contents: Tools Special purpose tools Measuring Instruments Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Batteries This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course … from Jul 1st

Electronic fuel injection Efi Course in rawalpindi Murree road 03115193625, Efi Auto electrician EFI Course in rawalpindi murree road pakistan international college of technical education offer Electronic fuel injection course in rawalpindi admission open for admission and information call 03115193625 new session start. Efi The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. international college of technical education offer Efi Electronic Fuel injection Efi Course in rawalpindi murree road admission open for admission and information visit our website www.icollegete.com , www.courses.com

Electronic fuel injection Efi Course in Rawalpindi Murree road 03115193625, EFI Fuel injection Efi Course In Rawalpindi Murree road 03354176949 International college of technical education Offers EFI Auto Electrician Course For admission and queries call 03115193625, 03354176949 EFi Electronic Fuel Injection Course in Rawalpindi Punjab Pakistan The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. International college of technical education EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. International college of technical education offer Electronic Fuel injection Course in Rawalpindi murree road pakistan admission open for admission and information call 03115193625, 03354176949 for more information visit pour website www.icollegete.com.