Tp4056 lithium battery charger module

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / – 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

100% New and High Quality Micro USB TP4056 Dual Charging Module Input Voltage: 4.35V - 6V (recommended voltage 5v) Chargingcut-off Voltage: 4.2V (± 1%) Maximum Charging Current Output: 1000mA (1A) Battery Discharge Protection Voltage: 3.0V Charging Status LEDs:Red LED Charging, Green LED Fully Charged Note: The installation and usgae of these modules require some basic knowledge of electronics, if you dont know how to install, please don't buy it.

Manage the constant current to constant voltage charging of a connected lithium battery Over-discharge protection - keeps your battery from being discharged below 2.4V, a healthy minimum voltage level for your batteryIf a connected battery has been discharged below 2.4V the module will cut output power from the battery until the battery voltage has been re-charged above 3.0V (the over-discharge release voltage), which at that time the module will again allow discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows charging of the battery to occur through the parasitic diode of the discharge control MOSFET (FS8205A Dual MOSFET). Overcharge protection - the module will safely charge your battery to 4.2V Overcurrent and short-circuit protection - the module will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs Soft-start protection limits inrush current Trickle charge (battery reconditioning) - if the voltage level of the connected battery is less than 2.9V, the module will use a trickle charge current of 130mA until the battery voltage reaches 2.9V, at which point the charge current will be linearly increased to the configured charge current.

Module name: 3S 12.6V Li-ion Lithium Battery 18650 Charger Protection Board Suitable range: For nominal voltage 3.6V 3.7V lithium battery(Including 18650,26650, lithium polymer batteries) Charging voltage: 12.6V Maximum output current: 20A Maximum output power / charging power: 252W Color: green material: plastic Product size:59*20*3.4mm Product weight: 4.4g Package Contents: 1 PCS x 3 string 12.6V 20A 18650 lithium battery protection board Precautions: 1.Strictly according to the diagram wiring: 0V/4.2V/8.4V/12.6V,Otherwise it will cause damage to the chip. 2.After connection,it need to first charge activation, then will have the output.

Size: approx.50x16x1mm Maximum discharge current: 10A Overcharge detection voltage: 4.25-4.35V±0.05V Over-discharge detection voltage: 2.3-3.0V±0.05V Maximum working current: 5A-8A Transient current: 9A-10A Operating temperature: -40~50? Storage temperature: -40~80? Quiescent current: <6uA Internal resistance: <60mO Service life: >30,000 hours

Module based on:TP4056 The module can manage battery charging and discharging, and also has built in boost converter to boost the voltage to match load conditions Charging voltage: 4.2V DC Charging current: Max. 1A Discharging current: Max. 2A Input voltage: 4.5-8V DC Output voltage: 4.3-27V DC (Continuously adjustable) Size: 3.3x2.3cm/1.3x0.91"

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / - 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.