Station open points

D-Link DWL-6610AP Wireless AC1200 Dual‑Band Unified Access Point Product Status The DWL-6610AP is an affordable, Unified Wireless AC1200 Access Point, enabling businesses of all sizes create the fastest wireless network possible.  With a sleek and stylish design, the DWL-6610AP can be discreetly deployed anywhere. Performance without Compromise       The DWL-6610AP is an affordable, Unified Wireless AC1200 Access Point, enabling businesses of all sizes create the fastest wireless network possible. With a sleek and stylish design, the DWL-6610AP can be discreetly deployed anywhere. Key Features Wireless AC 1200 Maximum combined wireless speed of 1200 Mbps.* Broadcast on 32 SSIDs Simultaneously Supports up to 32 SSIDs, 16 per radio, including station isolation. Dual Band Supports both 2.4Ghz and 5Ghz bands simultaneously. Unified Wireless Access points can be managed by unified wireless controller. Smart Design The DWL-6610AP can be mounted easily onto any wall or ceiling without looking out of place in an office or home. Enclosed in a plenum-rated UL2043 certified housing, the DWL-6610AP adheres to strict fire codes for placement in air passageways. Band Steering technology With band steering, the DWL-6610AP detects whether or not the wireless client is dual-band capable, and if so, it pushes the client to connect to the less congested 5 Ghz band. It does this by actively blocking the client’s attempts to associate with the 2.4 Ghz network. Versatility Built as standard Whether you intend to use a single Access Point or roll out a large corporate network, the DWL-6610AP coupled with a D-Link Wireless Controller or Unified Switch makes managing your wireless network simple. Secure and Green Design The DWL-6610AP has a wireless scheduler feature, which turns off wireless functionality when it isn’t needed, saving power and increasing network security.   Fast Seamless Roaming Combining the DWL-6610AP with a Unified Wireless Switch or Controller allows you to create a wireless network that enables people to move freely around a building without losing connectivity.     Management platforms D-Link’s Unified Wireless Access Points can be managed using a D-Link Wireless Controller or Unified Switch.   Simultaneous Dual-Band Supports up to 867 Mbps 2x2 MIMO for the 5Ghz band and up to 300Mbps 2x2 MIMO for the 2.4Ghz band   * Maximum wireless signal rate derived from IEEE standard 802.11ac specifications which are subject to change. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors may adversely affect wireless signal range. Specs Type Hardware-managed AP Wireless standard Wireless AC Frequency band mode Dual-band simultaneous Wireless speed 300 Mbps 2.4 GHz  867 Mbps 5 GHz Antenna type Embedded omni-directional antennas Antenna gain 3.5 dBi for 2.4 GHz  5 dBi for 5 GHz Power-over-Ethernet Yes Wired interface 1 x Gigabit Ethernet LAN Console port   Indoor/outdoor Indoor Type of housing Plastic Plenum rated (UL-2043)   Wireless modes Access Point (AP)  WDS bridge Advanced features MIMO Maximum number of SSIDs 16 per radio Auto channel selection   WMM-PS/802.11e (U-APSD)   Wi-Fi scheduler   AP traffic load balance   L2 roaming   WPA/WPA2-Personal/Enterprise   TKIP/AES encryption   WLAN partition   SSID broadcast disable   Rogue AP detection   Station isolation   MAC address filtering   802.1X authentication   Wireless controller/unified switch managed features AP load balance  Auto-channel, auto-RF management  Captive portal  L2/L3 fast roaming  Rogue AP mitigation  View neighbour AP information  WIDS/WIPS Supported D-Link Wireless Controllers/Unified Switches DWC-1000  DWC-2000  DWS-4026 Management platform Hardware controller: DWC/DWS Series WEB   SNMP (v1, v2c, v3)   Telnet   SSH   Configuration group sync through AP Array (up to 8 APs)  

Description: Details iShopping.pk brings you the best price for Vivotek 5MP Outdoor Panoramic Camera with Fisheye Lens (SF8174) with 1 year international warranty and express shipping all over Pakistan.     Specification: Camera Image Sensor 1/2.5" Progressive CMOS sensor in 2560 x 1920 resolution Maximum Resolution 1920 x 1920 (3 MP) Lens Type Fixed Focal Length f = 1.5 mm Aperture F2.8 Field of View 180° (horizontal) 180° (vertical) 180° (diagonal) Shutter Time 1/5 sec to 1/32,000 sec WDR Technology WDR enhanced Day & Night Removable IR-cut filter for day & night function Minimum Illumination 0.5 lux @ F2.8, 30 IRE (color) 0.001 lux @ F2.8, 50 IRE (B&W) Pan/Tilt/Zoom ePTZ 12x digital zoom (12x on IE plug-in) On-board Storage MicroSD/SDHC/SDXC card slot Video Compression H.264, MPEG-4 & MJPEG Maximum Frame Rate H.264: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 MPEG-4: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 MJPEG: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 Maximum Streams 3 simultaneous streams S/N Ratio Above 62 dB Dynamic Range 57 dB Video Streaming Adjustable resolution, quality and bit rate Image Settings Adjustable image size, quality, and bit rate Pixel counter Time stamp, text overlay, flip, and mirror Configurable brightness, contrast, saturation, sharpness, white balance, exposure control, gain, backlight compensation, and privacy masks Scheduled profile settings Video Motion Detection 5-window video motion detection Audio Audio Capability Audio input / audio output (full duplex) Effective Range 16.4' (5.0 m) Compression AAC G.711 G.726 Interface Built-in microphone External microphone input Network Users Live viewing for up to 10 clients Protocols IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS, PPPoE, CoS, QoS, SNMP, 802.1X, UDP, and ICMP Interface 10Base-T / 100BaseTX Ethernet (RJ-45) ONVIF Supported System Information CPU Multimedia SoC (System-on-Chip) Flash 128 MB RAM 128 MB Alarm and Event Alarm Triggers Video motion detection, manual trigger, digital input, periodical trigger, system boot, recording notification, and camera tampering detection Alarm Events Event notification using digital output, HTTP, SMTP, FTP and NAS server File upload via HTTP, SMTP, FTP and NAS server System Requirements Operating System Microsoft Windows 7 / Vista / XP / 2000 Browser Mozilla Firefox 7 to 10 (Streaming only) Internet Explorer 7/8/9/10 Other Players VLC: 1.1.11 or above QuickTime: 7 or above General Connectors RJ-45 cable connector for Network/PoE connection Audio input Audio output 12 VDC power input 1 x Digital input, 1 x Digital output LED Indicator System power and status indicator Power Input 12 VDC 802.3af Power-over-Ethernet (Class 2) Power Consumption Maximum 5.1 W (12VDC)  Maximum 5.3 W (PoE) Safety Certification CE C-Tick FCC (Class A) LVD UL VCCI Operating Temperature Starting Temperature: -13 to 122°F (-25 to 50°C) Working Temperature: -40 to 122°F (-40 to 50°C)     Product Overview: The  VIVOTEK SF8174 5MP Outdoor Day/Night Panoramic PTZ Network Dome Camera with Fisheye Lens  features a 5MP resolution 1/2.5" progressive CMOS sensor that offers high-quality image. Equipped with a fisheye lens for 360° surround view (ceiling/floor/table mount) without blind spots, the camera provides a coverage of wide and open areas such as airports, shopping malls, parking lots, retail stores, offices, and more. The SF8174 Camera comes with a removable IR-cut filter, maintaining clear images 24 hours a day. Together with 802.3af compliant PoE, MicroSD/SDHC/SDXC card slot for on-board storage, this camera is appropriate for constructing a robust surveillance system with the greatest coverage possible. Moreover, the SF8174 Camera is compatible with the proprietary Panoramic PTZ solution which lets the camera monitor open areas with extreme detail. The applications for the SF8174 camera include department stores, station lobbies, airports, parking lots, and any wide open area where comprehensive video surveillance systems and the capability for extreme video detail are essential. •  5MP CMOS sensor •  30 fps @ 1080p full HD •  1.5 mm fisheye lens for 180° panoramic view and 360° surround view •  Panoramic PTZ compatible •  Removable IR-cut filter for Day & Night function •  Real-time H.264, MPEG-4, and MJPEG compression (triple codec) •  WDR enhancement for unparalleled visibility in extremely bright or dark environments •  ePTZ for data efficiency •  Built-in 802.3af compliant PoE •  Built-in MicroSD/SDHC/SDXC card slot for on-board storage •  Pixel calculator for image clarity measurement

Description: Details iShopping.pk brings you the best price for Vivotek 5MP Outdoor Vandal Resistant Panoramic Camera with Fisheye Lens (SF8174V) with 1 year international warranty and express shipping all over Pakistan.     Specification: Camera Image Sensor 1/2.5" Progressive CMOS sensor in 2560 x 1920 resolution Maximum Resolution 1920 x 1920 Lens Type Fixed Focal Length f = 1.5 mm Aperture F2.8 Field of View 180° (horizontal) 180° (vertical) 180° (diagonal) Shutter Time 1/5 sec to 1/32,000 sec WDR Technology WDR enhanced Day & Night Removable IR-cut filter for day & night function Minimum Illumination 0.5 lux @ F2.8, 30 IRE (color) 0.001 lux @ F2.8, 50 IRE (B&W) Pan/Tilt/Zoom ePTZ 12x digital zoom (12x on IE plug-in) On-board Storage MicroSD/SDHC/SDXC card slot Video Compression H.264, MPEG-4 & MJPEG Maximum Frame Rate H.264: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 MPEG-4: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 MJPEG: 15 fps at 1920 x 1920, 30 fps at 1920 x 1080 Maximum Streams 3 simultaneous streams S/N Ratio Above 62 dB Dynamic Range 57 dB Video Streaming Adjustable resolution, quality and bit rate Image Settings Adjustable image size, quality, and bit rate Pixel counter Time stamp, text overlay, flip, and mirror Configurable brightness, contrast, saturation, sharpness, white balance, exposure control, gain, backlight compensation, and privacy masks Scheduled profile settings Video Motion Detection 5-window video motion detection Audio Audio Capability Audio input / audio output (full duplex) Effective Range 16.4' (5.0 m) Compression AAC G.711 G.726 Interface Built-in microphone External microphone input Network Users Live viewing for up to 10 clients Protocols IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS, PPPoE, CoS, QoS, SNMP, 802.1X, UDP, and ICMP Interface 10Base-T / 100BaseTX Ethernet (RJ-45) ONVIF Supported System Information CPU Multimedia SoC (System-on-Chip) Flash 128 MB RAM 128 MB Alarm and Event Alarm Triggers Video motion detection, manual trigger, digital input, periodical trigger, system boot, recording notification, and camera tampering detection Alarm Events Event notification using digital output, HTTP, SMTP, FTP and NAS server File upload via HTTP, SMTP, FTP and NAS server System Requirements Operating System Microsoft Windows 7 / Vista / XP / 2000 Browser Mozilla Firefox 7 to 10 (Streaming only) Internet Explorer 7/8/9/10 Other Players VLC: 1.1.11 or above QuickTime: 7 or above General Connectors RJ-45 cable connector for Network/PoE connection Audio input Audio output 12 VDC power input 1 x Digital input, 1 x Digital output LED Indicator System power and status indicator Power Input 12 VDC 802.3af Power-over-Ethernet (Class 2) Power Consumption Maximum 5.1 W (12VDC)  Maximum 5.3 W (PoE) Casing Vandal-proof IK10-rated metal housing, weather-proof IP66-rated Safety Certification CE C-Tick FCC (Class A) LVD UL VCCI, EN50155 Operating Temperature Starting Temperature: -13 to 122°F (-25 to 50°C) Working Temperature: -40 to 122°F (-40 to 50°C)     Product Overview: The  VIVOTEK SF8174V 5MP Outdoor Day/Night Vandal-Resistant Panoramic PTZ Network Dome Camera with Fisheye Lens  features a 5MP resolution 1/2.5" progressive CMOS sensor that offers high-quality image. Equipped with a fisheye lens for 360° surround view (ceiling/floor/table mount) without blind spots, the camera provides coverage of wide and open areas such as airports, shopping malls, parking lots, retail stores, offices, and more. The camera comes with a removable IR-cut filter, maintaining clear images 24 hours a day. The IP66-rated housing is designed to help the camera body withstand rain and dust and ensures operation under harsh weather conditions; additionally, the vandal-proof IK10-rated housing provides protection from physical damage. Together with 802.3af compliant PoE, microSD/SDHC/SDXC card slot for on-board storage and EN50155, this camera is appropriate for constructing a robust surveillance system. Moreover, the SF8174V Camera is compatible with the proprietary Panoramic PTZ solution which lets the camera monitor open areas with extreme detail. The applications for the SF8174V camera include department stores, station lobbies, airports, parking lots, and any wide open area where a comprehensive video surveillance system and extreme video detail are essential. •  5MP CMOS sensor •  30 fps @ 1080p full HD •  1.5 mm fisheye lens for 180° panoramic view and 360° surround view •  Panoramic PTZ compatible •  Removable IR-cut filter for Day & Night function •  Real-time H.264, MPEG-4, and MJPEG compression (triple codec) •  WDR enhancement for unparalleled visibility in extremely bright or dark environments •  Vandal-proof IK10-rated and weather-proof IP66-rated housing •  ePTZ for data efficiency •  Built-in 802.3af compliant PoE •  Built-in MicroSD/SDHC/SDXC card slot for on-board storage •  Pixel calculator for image clarity measurement.

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Stonex R1 Plus Total Station, precise distance and angles measurements, concentrated in 5 Kg of pure technology. The perfect tool whenever the topographic works requires a light and fast machine, all day working thanks to 26 hours of continuous operating time. The onboard field programs, included as standard, make R1 Plus suitable for any construction site, cadastral, mapping and staking out, works. No limitation for distance measurements, up to 5.000 m with a single prism – 600 m reflectorless (KGC 90%) – and 2” as angular accuracy, always guarantee a reliable points calculation. R1Plus has been designed to hold out against rain and dust: the IP66 certification allows to go ahead with the survey even during hard rain. The body design is distinguished by its robust mechanical structure, and the high performance telescope, featuring 30X magnification and illuminated reticle, provide the best sighting quality in any lighting condition.

Description: Details iShopping.pk brings you the best price for Asus TUF GT501 ATX Mid-Tower Gaming CPU Case  with express shipping all over Pakistan.     Features: • Designed to be noticed: Metal front panel with custom TUF Gaming spatter pattern, and 4mm-thick, smoked, tempered-glass side panel to showcase your build’s internals. • Mobile battle station: Ergonomic, woven-cotton carry handles enable easy and safe transport up to 30Kg. • Efficient cooling: Equipped with three 120mm Aura Sync RGB-illuminated fans and one 140mm rear PWM fan, plus up to seven fan-mounting points for targeted airflow. • Space reserved for both front- and top-mounted 360mm water-cooling radiators plus a 140mm radiator at the rear. • Perfect for TUF Gaming motherboards: Fan and cable placement optimized for TUF Gaming gear, and ready for perfect cooling control via our Fan Xpert 4 software.   Specifications:   Dimensions 251 x 545 x 552 mm (WxDxH) Case Size ATX Mid Tower Form Factor ATX/micro ATX/Mini ITX/EATX (12”x10.9”) Drive Bays 4 x Int x 2.5”/3.5” Combo Bay 3 x Int x 2.5” Bay System Fan Support Pre-installed Fans Front: 3x 120mm AURA RGB (1200RPM) Rear: 1 x 140 PWM Expansion Slots 7+2 (additional vertical) Weight N.W. 10.5 kg Color Black Front I/O Ports 2 x USB 3.1 Gen1 1 x Headphone 1 x Microphone

Description: Details iShopping.pk brings you the best price for Gamdias Talos E2 Elite RGB Tempered Glass Mid-Tower Gaming Case Black with express shipping all over Pakistan.   Details:   The TALOS E2 Elite mid-tower again features the trapezoidal tempered glass front panel and eye-catching trio of 120mm ARGB lighting fans. With the new side swinging magnetically closing tempered glass side panel to top any extravagant ARGB battle station.   Smooth and Uninterrupted With a trapezoidal tempered glass and three built-in 120mm ARGB fans to allow high air flow go through the aggressive angled slots.   One Press and Sync All Handy I/O port on the top of the case featuring a ARGB fans control button, allowing you to cycle through all the lighting effects by simply pressing a button. A 3-sec hold of the button will sync the fans to your RGB motherboard 5v 3-pin. A high-speed USB 3.0, two USB 2.0 ports, a HD audio jack and a power button can also be found on the I/O port.   Magnetic Dust Filter A magnetically held dust filter, located on top of the TALOS E2 Elite to minimize dust entering the case. With magnets holding the filter to the case, makes it easy to remove and clean the washable dust filter.   Out of the Ordinary The TALOS E2 Elite comes with a single side magnetic closing tempered glass swinging door. Not only showcasing all the components, also makes modding easier and more convenient.   Ample Accommodation The accommodation inside TALOS E2 Elite is able to support up to six 120mm fans. Mounting points for 280mm, 240mm radiators at the top and additional 360mm at front, 140mm or 120 mm radiator in the rear.   Elite Expansion The TALOS E2 Elite’s internal volume is 15% larger than it’s predecessor, capable of supporting high-end CPU coolers, VGA cards up to 340mm and PSU up to 180mm long. An additional 3 Slot Vertical VGA Slot is also now available.   Clean slate A clean designed side glass panel without the thumb screws getting in the way visually. A unique designed mechanism which allows the side glass panel to slide and clip right into the case. Therefor you are able to function the 4mm tinted tempered glass with ease, which displays your internal rig components.

Detachable module for testing two remote points. Open/Short wiring test. Connected wires display. Ethernet 10 and BASE-2 termination value detector.