Relay module

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com SINGLE CHANNEL RELAY MODULE Product Description This 5V relay module is active HIGH meaning that HIGH level will activate the relay on and LOW level will deactivate it. Module can be controlled by a wide range of micro-controllers such as Raspberry Pi, Arduino, PIC, AVR, BeagleBone and many more. Convenient standard 2.54mm pitch input header and KF301 screw terminals for output means that no soldering is required, just connect your wires and module is ready for use. Module has two status LEDs built in. Red for board power and green for relay status. Includes 3 output terminals. Normally Closed (NC), Common and Normally Open (NO).

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com 2 CHANNEL 5V RELAY MODULE Description: The 2 channel 5V relay module provides 2 optically isolated inputs that accept a wide range of voltage, including the 3VDC and 5VDC signals available on the Arduino. This is a great way to switch on or off AC or DC loads using your Arduino. The relays are single-pole double-throw (SPDT) and are rated for 10A @ 250VAC. The ground for the relay coils is separate from the ground for the input signals. This, along with the optical isolation, provides a total galvanic isolation between the input and output. The two grounds could be joined together if desired with the included jumper. The relay coils run on 5VDC, and the module has screw-terminal blocks for sturdy and reusable attachments for the external load. The signal and power inputs run through the male single-row header.

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:03002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic .com Email : info @ matrixelectronic .com 8 Channel 5V Relay Module Description: This board provides 8 optically isolated inputs that accept a wide range of voltage, including the 3VDC and 5VDC signals available on the Arduino. This is a great way to switch on or off AC or DC loads using your Arduino! The relays are single-pole double-throw (SPDT) and are rated for 10A @ 250VAC. The ground for the relay coils is separate from the ground for the input signals.

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com 4 CHANNEL RELAY Module Specifications: Material: Mixed Material Dimensions (cm): 7.7 x 5.5 x 2 Weight (kg): 0.063 Control signal: the TTL level Rated load: 10A/250vAC 10A/125vAC 10A/30DC 10A/ 28vDC Rated by current: 10A (NO),5A (NC) Largest switching voltage: 250vAC,30 VDC Below contact action time: 10ms

Control high-power devices up to 10 A with a simple high/low signal Provides isolation between the microcontroller and device being controlled Screw terminals for relay connections 3-pin servo-style header for power/signal interface LED indicator provides visual feedback

Operating voltage: 6-30V Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable. Trigger Signal Source: High-Level Trigger (3.0 V-24 V) Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A Optocoupler Isolation.

Operating voltage: DC 6V-30V (supports micro USB 5V) Static current: 20mA Working current: 50mA Service life: more than 100,000 times Working temperature: -40°C to 85°C Size: 6.2*3.8*1.7cm (length*width*height)

Bi-directional isolated 4 channel relay control module, according to user's needs, it can choose high or low electrical level to control the pick-up of the relay. The module adopts high quality relay, industry top-most ultra small package optocouplers, high high dielectric transistor, RED signal lights. Double side plate, overall consideration layout after overall consideration, with its stable performance. It can be widely used in varieties of control occasions.

W1209 Temprature controller with casing Temperature control mode: ON / OFF Temperature range:-50-110 ResolutionWhen temperature is 0.1 the resolution is -9.9~99.9, other temperature segment is 1 Control accuracy: 0.1 Hysteresis accuracy: 0.1 Refresh rate: 0.5S High temperature protection 0-110 Supply voltage: for DC 12V Static current: ≤ 35MA, attract current ≤ 65MA Output voltage: for DC 12V Output power: 10A relay Measurement input: NTC (10K 0.5%) Waterproof Sensor Environmental requirements: -10 ~ 60 Humidity 20% -85% Digital Led Thermostat Temperature Control DC 12V Adapter Thermometer Thermo Controller Switch Module + NTC Sensor W1209

XH-M452 DC 12V LED Digital Thermostat Temperature Humidity Control Thermometer Hygrometer Controller Relay Module AM2301 ProbeSupports heating mode and cooling mode. High precision 0.1 Celsius and 0.1% RH. Real-time display of temperature and humidity. Custom load, arbitrarily selected. Simple setting. Easy installation. Power-down memory function.

ARDUINO EDUCATION STARTER KIT we also deals in variety of ARDUINO BOARDS with rock bottom price Specificatoin Arduino Education Starter Kit Specification: ARDUINO UNO R3 board * 1 High quality and large bread board * 1 RFID module * 1 IC Keychain * 1 Non-contact type IC card * 1 I2C 1602 LCD module * 1 5V Relay * 1 DS1302 clock module * 1 Voice detection module, * 1 Temperature and humidity module * 1 Level detection module, * 1 4 * 4 keypad module * 1 Three-color RGB module * 1 XY joystick * 1 Servo * 1 Stepper motor driver board * 1 Blue LED * 5 Yellow LED * 5 Red LED * 5 1k resistor * 5 10k ohm resistor * 5 220 ohm resistor * 8 Buzzer * 2 Key module (with hat) * 4 ROCKER SWITCH * 2 LM35 sensor module * 1 Photoresistor * 3 Fire * 1 Infrared receiver * 1 Adjustable potentiometer * 1 A digital control * 1 4 digital tube * 1 8 * 8 dot matrix module * 1 74HC595N chips * 1 Infrared remote control * 1 Breadboard Jumper 30 Male to Female DuPont lines * 30 9 volt battery snap * 1 USB Cable * 1 Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com

The range of w1209 digital temperature controller is -50 to 110C. Resolution of temperature module at -9.9 to 99.9 is 0.1C The resolution of the module at all other temperatures is 1C. The accuracy of the measurement of the W1209 Temperature Control Switch is 0.1 C. Its control accuracy is 0.1C. The module refresh rate is 0.5 Sec. The power controlling module input power is 12V. NTC is its measuring inputs. Its output consists of 1 channel relay and its capacity is 10A.

This project having Arduino Mega 2560, Zigbee Module, DHT11 sensors, GSM modem in it. with the help of this project we monitor 2 different room temperatures and humidity and with the help of relay we control it. It includes all reqd accesories and coding.Price are little bit negotiable. contact timing # 5:00 pm-12:00 pm.

Description: Details iShopping.pk brings you the best price for TP-Link 300Mbps Wireless N VDSL/ADSL Modem Router (TD-W9960) with express shipping all over Pakistan.   Features: • Versatile Connectivity - With DSL and LAN / WAN ports, the TD-W9960 is fully compatible with the VDSL2 / ADSL2 + / ADSL2 / ADSL standards and also works with fiber / cable access. • Boosted Speeds - Superfast VDSL broadband speeds of up to 100Mbps together with 300Mbps Wi-Fi. • Maximized Range - Powerful external antennas provide far-reaching wireless coverage in every direction. • Effortless Management - Set up in minutes with the powerful Tether app or intuitive web interface and manage the network from anywhere   Specification: HARDWARE Interface 3 10 / 100Mbps RJ45 LAN Ports  1 10 / 100Mbps RJ45 LAN / WAN Port  1 RJ11 Port Buttons WPS Button  RESET Button  Power ON / OFF Button External power supply 9VDC / 0.6A IEEE Standards IEEE 802.3, 802.3u VDSL2 Standards ITU-T G.993.2  ITU-T G.993.5 (G.vector)  ITU-T G.998.4 (G.INP) Dimensions (WxDxH) 181.6 * 129.7 * 36.2mm Antenna type Omni directional, Fixed Antenna gain 2 x 5dBi WIRELESS MODULE SETTINGS Wireless Networking Standards IEEE 802.11b, 802.11g, 802.11n Frequency range (reception and transmission) 2.400-2.4835GHz EIRP (Wireless signal power) Wireless Security 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA-PSK2  encryptions, Wireless MAC Filtering CHARACTERISTICS OF THE SOFTWARE QoS (data prioritization) WMM, Bandwidth Control (IP QoS) Security NAT Firewall, SPI Firewall, Denial of Service (DoS), SYN Flooding, Ping of Death, Access Control, Service Filtering, IP and MAC Address Binding Operating modes VDSL / ADSL Modem Router, Wireless Router, Control Web Based Configuration (HTTP), Remote Management, CWMP (TR-069), Web Based Firmware Upgrade, Diagnostic Tools Port Forwarding Virtual Server, Port Triggering, DMZ, ALG, UPnP VPN traffic skip IPSec VPN Protocols Supports IPv4 and IPv6 ATM / PPP protocols PPPoE (RFC2516)  PPPoA (RFC 2364)  MER / IPoE (RFC 1483 Routed)  IPoA (RFC1577 / 2225)  Bridge (RFC1483 Bridge) Additional Features Parental Controls, Network Address Translation (NAT), Port Mapping (Grouping), Static Routing, RIP v1 / v2 (optional), DNS Relay, DDNS, IGMP V1 / V2 / V3 APP Tether App OTHER Certification CE, RoHS System requirements Microsoft Windows 98SE, NT, 2000, XP, Vista ™ or Windows 7, 8, 8.1, 10,  the Mac OS, the NetWare, the UNIX or the Linux  of Internet Explorer 11, of Firefox 12.0, the Chrome 20.0, the Safari 4.0, or OTHER  the Java-the enabled browser  the Subscription With an internet service provider (for internet access) Environmental parameters Operating Temperature: 0 ℃ ~ 40 ℃ (32℉ ~ 104℉  Storage ) Storage Temperature: -40 ℃ ~ 70 ℃ (-40℉ ~ 158℉)  Operating Humidity: 10% ~ 90% non-condensing  Storage Humidity: 5% ~ 90 % Non-condensing   Intended use of the device TD-W9960 from TP-Link supports the new standard ITU-T G.993.2 VDSL2, which provides incoming and outgoing streams up to 100 Mbps. The device is compatible with ADSL, fiber optic and cable modem. Due to the speed of Wi-Fi up to 300 Mbps on 2.4 GHz, the TD-W9970 is an excellent choice for users who need high-quality HD video, online games and resource-intensive tasks without delays.   Switchable LAN / WAN port - compatible with cable / fiber optic modems The TD-W9970 supports connection over VDSL / ADSL or Ethernet WAN (EWAN), which provides flexible access to the Internet. With the switchable LAN / WAN port, the device is compatible with cable and fiber-optic modems. This unique feature is especially useful when users want to switch from VDSL / ADSL to fiber or cable.   Broadband connection up to 100 Mbps The TD-W9970 supports VDSL2, is backwards compatible with ADSL2 + / ADSL2 / ADSL and provides up to 100 Mbps throughput. It is designed for simultaneous transmission of voice and video, data, HDTV stream and online games.