Pa wireless

  Technical Specifications Wireless Headset Circumaural Design with 50mm Driver Units Volume & Mic Control Buttons on the Headset Detachable 2.5mm Microphone Cable Dimensions: 200mm(W) * 204mm(H) * 88mm(D) Headphones Radio Frequency: 2.4GHz Wireless Range: 33ft / 10m Frequency Response: 20 - 20,000 Hz Impedance: 32O at 1kHz Sensitivity (@1kHz, 1V/Pa): 105dB +/- 2dB Drivers: 50 mm, with Neodymium Magnets Batteries: 2 AAA Batteries (Up to 12 Hours Battery Life) Charging Time: 3 Hours Microphone Frequency Response: 130 - 10,000 Hz Sensitivity (@1kHz, 1V/Pa): -42 ± 2dB Signal-to-Noise Ratio: >55 dB Pick-up Pattern: Uni-directional Hardware Requirements Xbox 360® Composite Cable (or Component HD AV Cable) PC 3.5mm Headphone and Mic Cables* Available 3.5mm Headphone Jack Available 3.5mm Microphone Jack * 3.5mm headphone and mic cables required and sold separately    

  Technical Specifications Wireless Headset Circumaural Design with 50mm Driver Units Volume & Mic Control Buttons on the Headset 3 Preset EQ Detachable 2.5mm Microphone Cable Dimensions: 200mm(W) * 204mm(H) * 88mm(D) Inner Ear Cup Diameter: 55 mm / 2.16” Approximate Weight (including batteries): 369 g / 0.81 lbs Headphones Radio Frequency: 5.8GHz Dolby® Headphone / Dolby Pro Logic® II / Dolby Digital Wireless Range: 33ft / 10m Frequency Response: 20 - 20,000 Hz Impedance: 32O at 1kHz Sensitivity (@1kHz, 1V/Pa): 105dB +/- 2dB Drivers: 50 mm, with Neodymium Magnets Batteries: 2 AAA Batteries (Up to 8 Hours Battery Life) Charging Time: 3 Hours Microphone Frequency Response: 130 - 10,000 Hz Sensitivity (@1kHz, 1V/Pa): -42 ± 2dB Signal-to-Noise Ratio: >55 dB Pick-up Pattern: Uni-directional Hardware Requirements Xbox 360® Available Optical Port PC RCA to 3.5mm Cable* Available 3.5mm Headphone Jack Available 3.5mm Microphone Jack * RCA to 3.5mm cable required and sold separately    

Description: Details iShopping.pk brings you the best price for Mercusys 300Mbps High Power Wireless N Router (MW330HP) with express shipping all over Pakistan.   Features: • 300Mbps wireless speed – ideal for fast video streaming, online gaming and file downloads • Turbo button – instantly enhances the Wi-Fi signal and expands wireless coverage • PA chip – provides up to 2x transmission power, strong enough to penetrate walls and other obstacles • High gain 7dBi antennas – strongly boosts wireless range and coverage • Easy installation – intuitive webpage guides you through the setup process in minutes   Specifications: Dimensions (W X D X H) 192mm_127mm_36mm External Power Supply 9V/0.6A Antenna Type 3 * 7dBi Signal Rate 11n: Up to 300Mbps (Dynamic) 11g: Up to 54Mbps (Dynamic) 11b: Up to 11Mbps (Dynamic) Button TURBO, WPS/RESET Wireless Standards IEEE 802.11b/g/n Frequency 2.402-2.482GHz Reception Sensitivity 270M: -74dBm@10% PER_ 130M: -76dBm@10% PER_ 54M: -78dBm@10% PER 11M: -90dBm@10% PER 6 M: -94dBm@10% PER 1 M: -96dBm@10% PER Interfaces 3*10/100Mbps LAN Ports 1*10/100Mbps WAN Port Package Contents 300Mbps High Power Wireless N Router (MW330HP) Power Adapter Quick Installation Guide Ethernet Cable Environment Operating Temperature: 0_C~40_C (32_F~104_F) Storage Temperature: -40_C~70_C (-40_F~158_F) Operating Humidity: 10%~90% Non-Condensing Storage Humidity: 5%~90% Non-Condensing Transmission Power Wireless Security WPA-PSK / WPA2-PSK Wireless Functions Enable/Disable Wireless Radio, WDS Bridging WAN Type Dynamic IP/Static IP/PPPoE/PPTP/L2TP Management Access Control Local Management Remote Management DHCP Server Port Forwarding Virtual Server, UPnP, DMZ Firewall Security IP and MAC Address Binding Guest Network 2.4GHz Guest Network

  Specifications Speaker Drivers Headphone Frequency Response 20–20000 Hz Headphone Sensitivity 98 dBSPL Headphone Impedance 32 Ohm Headphone Total Harmonic Distortion Headphone Volume Control 40 mm Microphone Frequency Response 100–6500 Hz Type Detachable boom Sensitivity -38 dBV/Pa Polar Pattern Bidirectional Noise-Canceling Wireless Type Lossless 2.4 GHz Range 30ft / 9m Battery Life 20 hours Box Content Product Information Guide Arctis 1 Wireless Headset USB-C Wireless Transmitter USB-A adapter cable 4-pole 3.5mm audio cable    

Description: Details iShopping.pk brings you the best price for Sennheiser Lavailer Clip-On Wireless Microphone Set (XSW 12-C) with express shipping all over Pakistan.   Make your presentations come to life! Compact bodypack system, with omnidirectional lavalier mic, offering excellent speech intelligibility. Transmitter features an illuminated mute button, 10 hours of operation, and 960 tunable frequencies. Unobtrusive ME2-2 lapel mic provides natural speech reproduction. All-metal, True Diversity receiver offers intuitive scan and sync functions that ensure trouble-free operation. Rugged, reliable and easy-to-use, XS Wireless delivers renowned Sennheiser sound to small venues, conference rooms or houses of worship.   Features: • Easy-to-use, all-in-one package for singers, speakers and presenters •  e 835 sound to cut through high on-stage levels •  High feedback rejection •  Mute button for full speech control •  Synchronization via RF remote channel •  Frequencies tunable in steps of 25 kHz •  24 MHz bandwidth •  8 frequency banks with each max 12 presets   Specification: Technical Data RF frequency range 821...832 MHz / 863...865 MHz  766...790 MHz  614...638 MHz  606...630 MHz  548...572 MHz  548...865 MHz Presets 12 THD, total harmonic distortion Signal-to-noise ratio > 103 dB(A) Transmission/receiving frequencies 960 (520 in range E) Switching bandwidth 24 MHz (13 MHz in range E) Receivers Dimensions 200 x 127 x 42 mm Weight ~ 730 g Antenna connector 2 BNC, 50 Ω Audio output level (balanced) XLR: +14 dBu max Audio output level (unbalanced) Jack: +8 dBu max Diversity reception True Diversity Transmitter Dimensions 96 x 66 x 24 mm Frequency response Mic: 100...16000 Hz  Line: 60...16000 Hz Weight ~ 95g RF Output Power typ. 10 mW Operating Time 10h Power Suppy 2x AA Batteries Input Voltage Range 0.5 Vrms Clip-on Microphone Microphone permanent polarized Sound pressure level (SPL) 142 dB Weight ~ 240 g Transducer Principle permanently polarized condenser microphone Pick-up pattern Omni directional AF sensitivity 5 mV/Pa

Logitech H800 Bluetooth Wireless Headset Price in Pakistan PC, smartphone and tablet headset: Easy to connect and switch between devices Rich digital stereo sound: Laser-tuned speaker drivers, built-in equalizer and noise-cancelling mic for crystal clear calls and music*. Sensitivity (microphone)- -47dBV/Pa +/- 3dB. Sensitivity (headphone)- 97dB +/-3dB 40 ft. wireless range: Listen and chat up to 12 m from your PC-or pair with your smartphone or tablet using Bluetooth. Input impedance: 32 Ohms Six-hour rechargeable battery: Listen and chat longer with easy USB charging. Frequency response (Headset): Wideband: 30Hz to 15KHz, Narrowband: 40Hz to 3.2KHz. Frequency response (Microphone): 100Hz to 6,500Hz Padded comfort: Adjustable padded headband and sculpted ear cups for a feel-good fit

HyperX Cloud II Wireless The HyperX Cloud was built to be an ultra-comfortable gaming headset with amazing sound. We put a lot of thought into the details of our HyperX signature memory foam, the premium leatherette, clamping force, and weight distribution to create a headset that’s comfortable through long gaming sessions. It’s no wonder that it’s become the preferred gaming headset for millions of gamers. Whether you want to focus on the competition or relax with some of your favorite games, there’s a Cloud that’s perfect for you. Driver Dynamic, 53mm with neodymium magnets Type Circumaural, Closed back Frequency response 15Hz–20kHz Impedance 60 Ω Sound pressure level 104dBSPL/mW at 1kHz T.H.D. ≤ 1% Weight 300g Weight with mic 309g Cable length and type USB charge cable (0.5m) Battery life2 30 hours Wireless Range3 2.4 GHz Up to 20 meters Microphone Element Electret condenser microphone Polar pattern Bi-directional, Noise-cancelling Frequency response 50Hz-6.8kHz Sensitivity -20dBV (1V/Pa at 1kHz) ENJOY FREE SHIPPING & DELIVERY: We at Shopon. pk provide you with a free delivery service facility, so now there is no need to go anywhere. You can place an order for your desired Headset from any brand mentioned on our website and we will deliver it to you within no time. SHOPON’S VISION Our vision is to ensure a future where a target customer will feel no fear while shopping online. We know that the online retail industry has yet to see its boom in Pakistan, and we are trying smart to provide our customers with a safe, swift, and efficient online buying experience. Unlike some big names on Pakistan’s online retail horizon, we are not a marketplace that would let anyone sell their merchandise on our store; to ensure quality, customer service, and customer retention, we made Shopon into a single entity online retail store. However, we do let independent sellers sell their high-quality products after we make them go through rigorous vetting and scrutiny. SHOPON’S MISSION It is Shopon’s mission to make 2022 Pakistan’s best year so far in terms of online shopping. We are striving hard to bring high-quality products to our customers via our single entity retail operation.

HyperX Cloud II Wireless The HyperX Cloud was built to be an ultra-comfortable gaming headset with amazing sound. We put a lot of thought into the details of our HyperX signature memory foam, the premium leatherette, clamping force, and weight distribution to create a headset that’s comfortable through long gaming sessions. It’s no wonder that it’s become the preferred gaming headset for millions of gamers. Whether you want to focus on the competition or relax with some of your favorite games, there’s a Cloud that’s perfect for you. Driver Dynamic, 53mm with neodymium magnets Type Circumaural, Closed back Frequency response 15Hz–20kHz Impedance 60 Ω Sound pressure level 104dBSPL/mW at 1kHz T.H.D. ≤ 1% Weight 300g Weight with mic 309g Cable length and type USB charge cable (0.5m) Battery life2 30 hours Wireless Range3 2.4 GHz Up to 20 meters Microphone Element Electret condenser microphone Polar pattern Bi-directional, Noise-cancelling Frequency response 50Hz-6.8kHz Sensitivity -20dBV (1V/Pa at 1kHz) ENJOY FREE SHIPPING & DELIVERY: We at Shopon. pk provide you with a free delivery service facility, so now there is no need to go anywhere. You can place an order for your desiredb'/xc2/xa0'Headsetb'/xc2/xa0'from any brand mentioned on our website and we will deliver it to you within no time. SHOPON’S VISION Our vision is to ensure a future where a target customer will feel no fear while shopping online. We know that the online retail industry has yet to see its boom in Pakistan, and we are trying smart to provide our customers with a safe, swift, and efficient online buying experience. Unlike some big names on Pakistan’s online retail horizon, we are not a marketplace that would let anyone sell their merchandise on our store; to ensure quality, customer service, and customer retention, we made Shopon into a single entity online retail store. However, we do let independent sellers sell their high-quality products after we make them go through rigorous vetting and scrutiny. SHOPON’S MISSION It is Shopon’s mission to makeb'/xc2/xa0'2022 Pakistan’s best yearb'/xc2/xa0'so far in terms ofb'/xc2/xa0'online shopping. We are striving hard to bring high-quality products to our customers via our single entity retail operation.

The PA-20 Portable Data Terminal (PDT) is a high performance wireless handheld mobile data capture device that scans and stores bar code data for upload to computer. The compact, industrial strength PA-20 features a superior scanner, large 16MB RAM memory, a color display, and a bold exterior design.Bluetooth capability allows wireless communication with peripheral devices within 30 meters. The PA-20 also supports RS-232 for transmitting data to a variety of devices, as well as USB for high speed transmission. Ideal for intensive commercial uses, the PA-20 is shockproof, dustproof, and waterproof in compliance with IP54. The ergonomic, professional keypad and pistol grip are made of wear-resistant rubber and are comfortable to operate. For dark environments the keypad uses a white backlight, and the PA-20 also vibrates for scanning confirmation in noisy or noise-sensitive environments. A 2.4-inch color LCD screen supports 12-, 16- and 24-dot fonts as well as multiple languages. The PA-20 offers tough connections via Pogo Pin and Cradle and high quality cable connections, so broken connections are not an issue. Rechargeable standard and pistol grip batteries provide extended battery life for longer scanning operation. Accessories include single cradle, four-slot cradle, holster with belt loop, charging and communication cable. 1 Sharp and bright color TFT QVGA display 2 Ergonomic, compact, robust and lightweight 3 Bluetooth technology 4 1.2m(4 ft) drop resistance 5 IP54 protection class 6 Quick attach handle 7 Extremely long operation hours

  General Specifications Driver size 8.6mm   Dynamic frequency response range 20Hz-20kHz   Sensitivity 96dB SPL/1mw   Sensitivity 96dB SPL1kHz   Sensitivity 96dB SPL/1m@1kHz dB v/pa   Impedance 16Ω   Weight (g) 16.2g Control and Connection Specifications Bluetooth transmitted power 0~4dBm   Bluetooth transmitted modulation GFSK, DQPSK, 8-DPSK   Bluetooth frequency 2.402GHz-2.48GHz   Bluetooth profiles HFP v1.5, HSP v1.2, A2DP v1.2, AVRCP v1.5   Bluetooth version V4.0 Powering Output Music play time with BT on >6hr   Talk time with BT on >6hr Battery Battery type GSP051230 01   Battery type Polymer Li-ion Battery (3.7V, 120mAh)   Charging time What's in the Box? 1 x pair of T110BT headphones 3 x sizes of ear tips (S, M, L) ICON charging cable Warning card Safety Sheet QSG    

  Features JBL Signature Sound Active Noise Cancelling Bluetooth 24-hour battery life with Bluetooth on and ANC off; 15-hour battery life with Bluetooth on and ANC on 2-hour charging for a full day entertainment Seamlessly switch between devices Comfort-fit fabric headband One-button remote with fabric cable Technical specifications: Driver size: 40mm Dynamic frequency response range: 20Hz–20kHz Sensitivity: 95dB Maximum SPL: 108dB Microphone sensitivity  @1kHz dB v/pa: -42 Impedance: 32 ohm Bluetooth transmitted power: 0-4dbm Bluetooth transmitted modulation: GFSK, π/4DQPSK, 8DPSK Bluetooth frequency: 2.402GHz–2.48GHz Bluetooth profiles: HFP v1.6, HSP v1.2, A2DP v1.2, AVRCP v1.4 Bluetooth version: V4.1 Battery type: Polymer Li-ion Battery (3.7V, 610mAh) Charging time: 2 hours Music play time with BT on and ANC on: Up to 15 hours Music play time with BT off and ANC on: Up to 30 hours Music play time with BT on and ANC off: Up to 24 hours Talk time with BT on: Up to 24 hours Weight (g): 258g    

Specifications Integrated Power over Ethernet Dual Band (2.4 GHz + 5 GHz) capability and speeds up to 600 Mbps* Industrial-strength Wi-Fi Protected Access (WPA, WPA2) security and data encryption IPv6 Support High Power PA for better Wi-Fi coverage        

BLOODY M70 GAMING TWS EARBUDS   (Black+Red) Price in Pakistan Stable, Reliable Bluetooth Connectivity Bluetooth v5.0 improves the stability of the wireless connection for more seamless audio and video sync and requires less power. Ultra-Low Latency Technology Bluetooth v5.0 Independent Transmission offers an extremely low input latency, which means its audio stays synced with your device and will never stutter. Game / Music Modes Featured by Smarter Listening Technology, it enhances your listening experience with Dual-Mode options. M.O.C.I. Dome Tech M.O.C.I. (Mycelium of Carbon IT) is the soul and heart of Golden Sound. Made of advanced biotechnology with bred nano mycelium and carbon fiber to offer the metal rigidity with paper-like thinness. This optimum diaphragm dome is made to create high-resolution and precise notes for highs and mids and unfolds music to its full potential. Extended Playtime 24H Battery life can last for up to 6-hours per charge, but no need for concern if you' re on-the-go. Simply recharge your earphones for another 18-hours playtime with the aluminum charging case. Wireless Transmission Independently Earbuds on either side of the ear works independently and transmits sound to left and right ears simultaneously. No need to worry about switching or missing a connection. The earbuds can take calls using either, or both, of the earbuds. This allows you to alternate their recharging. Control At Your Fingertips With just finger touch, you can use them to play/pause music, receive/end calls, switch modes, enter voice assistant(Siri, etc). Environmental Noise Cancellation Dual ENC noise cancelling microphone filters most ambient noises for prompt & clear teammate communication with crystal clarity. Water Resistant and Dust Resistant (IPX4) Ideal for those with an active lifestyle, you can work out to your favorite tunes and have the freedom to wear these wireless earbuds during a variety of outdoor activities. Slide-Lid Charging Case Magnetically sliding lid charging case flashes in neon backlight as you slide it open. Thanks to Automatic Connects Automatically connected to your phone as soon as you pull out from the case. Enter Voice Assistant Go smarter with your favorite voice assistant, Google Assistant and Amazon Alexa and Siri, etc. ALL DAY BATTERY LIFE PERFORMANCE Speaker Size: 6 mm Frequency Response: 20 Hz-20 kHz Earphone Sensitivity: 99 dB @ -10 dBFS Mic. Sensitivity: -42 dB @1 kHz/Pa Earphone Impedance: 16 ohm Bluetooth Version: v5.0 Operation Distance: 10 m Earphone Battery Type: Lithium Battery (60 mAh) Charging Case Battery Type: Lithium Battery (400 mAh) Charging Power: 5V=1A Earphone Charging Time: Case Charging Time: Music Playtime with Single Charge: ˜6H Playtime from Charging Case: ˜24H Weight: 55 g

BLOODY M70 GAMING TWS EARBUDS (Black+Blue) Price in Pakistan Stable, Reliable Bluetooth Connectivity Bluetooth v5.0 improves the stability of the wireless connection for more seamless audio and video sync and requires less power. Ultra-Low Latency Technology Bluetooth v5.0 Independent Transmission offers an extremely low input latency, which means its audio stays synced with your device and will never stutter. Game / Music Modes Featured by Smarter Listening Technology, it enhances your listening experience with Dual-Mode options. M.O.C.I. Dome Tech M.O.C.I. (Mycelium of Carbon IT) is the soul and heart of Golden Sound. Made of advanced biotechnology with bred nano mycelium and carbon fiber to offer the metal rigidity with paper-like thinness. This optimum diaphragm dome is made to create high-resolution and precise notes for highs and mids and unfolds music to its full potential. Extended Playtime 24H Battery life can last for up to 6-hours per charge, but no need for concern if you' re on-the-go. Simply recharge your earphones for another 18-hours playtime with the aluminum charging case. Wireless Transmission Independently Earbuds on either side of the ear works independently and transmits sound to left and right ears simultaneously. No need to worry about switching or missing a connection. The earbuds can take calls using either, or both, of the earbuds. This allows you to alternate their recharging. Control At Your Fingertips With just finger touch, you can use them to play/pause music, receive/end calls, switch modes, enter voice assistant(Siri, etc). Environmental Noise Cancellation Dual ENC noise cancelling microphone filters most ambient noises for prompt & clear teammate communication with crystal clarity. Water Resistant and Dust Resistant (IPX4) Ideal for those with an active lifestyle, you can work out to your favorite tunes and have the freedom to wear these wireless earbuds during a variety of outdoor activities. Slide-Lid Charging Case Magnetically sliding lid charging case flashes in neon backlight as you slide it open. Thanks to Automatic Connects Automatically connected to your phone as soon as you pull out from the case. Enter Voice Assistant Go smarter with your favorite voice assistant, Google Assistant and Amazon Alexa and Siri, etc. ALL DAY BATTERY LIFE PERFORMANCE Speaker Size: 6 mm Frequency Response: 20 Hz-20 kHz Earphone Sensitivity: 99 dB @ -10 dBFS Mic. Sensitivity: -42 dB @1 kHz/Pa Earphone Impedance: 16 ohm Bluetooth Version: v5.0 Operation Distance: 10 m Earphone Battery Type: Lithium Battery (60 mAh) Charging Case Battery Type: Lithium Battery (400 mAh) Charging Power: 5V=1A Earphone Charging Time: Case Charging Time: Music Playtime with Single Charge: ˜6H Playtime from Charging Case: ˜24H Weight: 55 g

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)