Output module

Module name: 3S 12.6V Li-ion Lithium Battery 18650 Charger Protection Board Suitable range: For nominal voltage 3.6V 3.7V lithium battery(Including 18650,26650, lithium polymer batteries) Charging voltage: 12.6V Maximum output current: 20A Maximum output power / charging power: 252W Color: green material: plastic Product size:59*20*3.4mm Product weight: 4.4g Package Contents: 1 PCS x 3 string 12.6V 20A 18650 lithium battery protection board Precautions: 1.Strictly according to the diagram wiring: 0V/4.2V/8.4V/12.6V,Otherwise it will cause damage to the chip. 2.After connection,it need to first charge activation, then will have the output.

Manage the constant current to constant voltage charging of a connected lithium battery Over-discharge protection - keeps your battery from being discharged below 2.4V, a healthy minimum voltage level for your batteryIf a connected battery has been discharged below 2.4V the module will cut output power from the battery until the battery voltage has been re-charged above 3.0V (the over-discharge release voltage), which at that time the module will again allow discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows charging of the battery to occur through the parasitic diode of the discharge control MOSFET (FS8205A Dual MOSFET). Overcharge protection - the module will safely charge your battery to 4.2V Overcurrent and short-circuit protection - the module will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs Soft-start protection limits inrush current Trickle charge (battery reconditioning) - if the voltage level of the connected battery is less than 2.9V, the module will use a trickle charge current of 130mA until the battery voltage reaches 2.9V, at which point the charge current will be linearly increased to the configured charge current.

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com SINGLE CHANNEL RELAY MODULE Product Description This 5V relay module is active HIGH meaning that HIGH level will activate the relay on and LOW level will deactivate it. Module can be controlled by a wide range of micro-controllers such as Raspberry Pi, Arduino, PIC, AVR, BeagleBone and many more. Convenient standard 2.54mm pitch input header and KF301 screw terminals for output means that no soldering is required, just connect your wires and module is ready for use. Module has two status LEDs built in. Red for board power and green for relay status. Includes 3 output terminals. Normally Closed (NC), Common and Normally Open (NO).

DESCRIPTION Feature: Can be easily installed in a variety of small devices. Use Micro USB input,USB charger or mobile power through the data line,to get 9V,12V,15V,18V,24V Portable and easy to use. Ultra wide input and output voltage, high conversion efficiency. Specifications: Product size:3cm×1.7cm Input voltage: 2 v – 24v Max output current: 2A non continuous Recommended continuous max 1A Max output voltage: > 28 V (recommended for use within 26V) Efficiency: > 93% (efficiency is related to the differential pressure of input and output). Note: 1) this module is a boost module, the output voltage is greater than the input voltage 2) the peak current output current is no more than 2A Mention that you found this ad on DealMarkaz.pk when you call.

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com FLAME SENSOR MODULE RED Description: flame wavelengths between 760 nm to 1100 nm infrared is most sensitive. Module has two outputs: 1, AO, analog output, real-time output voltage signal on the thermal resistanc 2, DO, when the temperature reaches a certain threshold, the output high and low signal threshold adjustable via potentiometer Power supply: DC 3-5.5VAnalog

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com Rain Detection sensor module Specification: Product use: rain, rain sensor, can be used for all kinds of weather monitoring, and translated into output signals and AO. The sensor USES the high quality FR - 04 double material, large area of 5.5 * 4.0 CM, treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance; The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA; With potentiometer sensitivity adjustmentThe working voltage of 3.3 V to 5 V The output format: digital switch output (0 and 1) and analog AO voltage output; Has a fixed bolt hole, convenient installation Small board PCB size: Approx. 3.2 cm x 1.5 cm The LM393, use of wide voltage comparator

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com 2 CHANNEL 5V RELAY MODULE Description: The 2 channel 5V relay module provides 2 optically isolated inputs that accept a wide range of voltage, including the 3VDC and 5VDC signals available on the Arduino. This is a great way to switch on or off AC or DC loads using your Arduino. The relays are single-pole double-throw (SPDT) and are rated for 10A @ 250VAC. The ground for the relay coils is separate from the ground for the input signals. This, along with the optical isolation, provides a total galvanic isolation between the input and output. The two grounds could be joined together if desired with the included jumper. The relay coils run on 5VDC, and the module has screw-terminal blocks for sturdy and reusable attachments for the external load. The signal and power inputs run through the male single-row header.

SD CARD READER MODULE 1.SD Card module can make your SD application more easier and simple. 2.It is easily interfaced as a peripheral to your arduino sensor shield module. 3.Through programming, you can read and write to the SD card using your arduino. 4.Can be used for SD Card more eaisly, such as for MP3 Player, MCU/ARM system control. 5.All SD SPI pins output, MOSI, SCK, MISO and CS. 6.Support 5V/3.3V input 7.PCB Dimensions: 47.6mm * 30.7mm * 1.6mm 8.Weight: 10g Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com

Description: Details iShopping.pk brings you the best price for Toa Electronics VoIP Paging Module Power Supply with express shipping all over Pakistan.   The SP-11N is a VoIP phone paging module supported SIP (Session Initiation Protocol) with Auto-answer function. It can be connected with IP network and directly registered as one SIP phone station on various management software of SIP server. It also has VOX and mute functions designed for use with TOA's 9000M2, 900, 700 and BG series amplifiers.   Specifications: General Product Type VoIP phone paging module Intended For Audio mixer Product Material Aluminum Width 1.4 in Depth 3.6 in Height 3.1 in Weight 3.03 oz Connections Connections LAN - RJ-45 Control output - 6 pin terminal block

The module is useful for detecting the presence of light. The module has two LEDs, one for power and one for output of the comparator. In this configuration, the circuit detects if the light exceeds a certain threshold.

Arduino 3-color LED Module With red, green and blue output Great for DIY project Dimensions: 0.98 in x 0.59 in x 0.08 in (2.5 cm x 1.5 cm x 0.2 cm)

This product is a non-isolated step-down module, the input voltage is DC3-38V, and the output voltage is 1.25~36VThe maximum output current is 5A, the maximum is 150W; it has a constant voltage and constant current dual adjustment function, high,High efficiency, it can be used as a charg adapter or directly connected to a load.

W1209 Temprature controller with casing Temperature control mode: ON / OFF Temperature range:-50-110 ResolutionWhen temperature is 0.1 the resolution is -9.9~99.9, other temperature segment is 1 Control accuracy: 0.1 Hysteresis accuracy: 0.1 Refresh rate: 0.5S High temperature protection 0-110 Supply voltage: for DC 12V Static current: ≤ 35MA, attract current ≤ 65MA Output voltage: for DC 12V Output power: 10A relay Measurement input: NTC (10K 0.5%) Waterproof Sensor Environmental requirements: -10 ~ 60 Humidity 20% -85% Digital Led Thermostat Temperature Control DC 12V Adapter Thermometer Thermo Controller Switch Module + NTC Sensor W1209

Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com SKM53 Gps module Description: Ultra high sensitivity: -165dBm 22 tracking/66 acquisition-channel receiver WAAS/EGNOS/MSAS/GAGAN support NMEA protocols (default speed: 9600bps) Internal back-up battery and 1PPS output One serial port and USB port (option) Embedded patch antenna 18.2 x 18.2 x 4.0 mm Operating temperature range: -40 to 85 RoHS compliant (Lead-free) Tiny form factor 30mm x20mm x 11.4mm

100% New and High Quality Micro USB TP4056 Dual Charging Module Input Voltage: 4.35V - 6V (recommended voltage 5v) Chargingcut-off Voltage: 4.2V (± 1%) Maximum Charging Current Output: 1000mA (1A) Battery Discharge Protection Voltage: 3.0V Charging Status LEDs:Red LED Charging, Green LED Fully Charged Note: The installation and usgae of these modules require some basic knowledge of electronics, if you dont know how to install, please don't buy it.

This module is a portable backup supply with an input that matches the 5.0V adapter to charge the internal.Use built-in for portable device to provide 5.0V/3.0A USB2.0 supply output for external devices.Protection: overcharge protection, overdischarge protection, short circuit protection, constant current.Charging cable: support three USB data cable charging, including Iphone and Android.

Reliable and fast data transfer. With this cable, you can connect your power bank to router. Thus, when power cut, you can use your power bank to supply your router! Internet blackout solve baby, continuous Artifact Use mobile power,charg treasure or notebook usb interface Drive after a power outage or optical router cat online Via computer USB jack to power other devices. Such as: USB lights, USB fan, Cartoon watches, radiator, 5V mini speakers, USB HUB, etc. Interface: USB transfer DC5.5 * 2.1MM(2.5MM) Input voltage: DC 5V Output voltage: DC 9V and 12V Max Color: Black Material: ABS Output current: For 800mA or less application is recommended Package includes: 1 X Conversion Line Only the above package content, other products are not included. Note: Light and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Operating voltage: 6-30V Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable. Trigger Signal Source: High-Level Trigger (3.0 V-24 V) Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A Optocoupler Isolation.

Interface: UART Operating Voltage: 3.3V - 5V The change range of output’s power: -4 - +6dBm. Has the external 8Mbit FLASH Range: Around 20m Password for connection: 1234 or 0000

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / – 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / - 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

Brand: Electrica Input Range: 3.8V- 32V Output Range:1.25V-35V Input Current:3A (max) Conversion efficiency:<94% Operating Temperature:-40 -+85 Voltage Regulation:± 0.5% Dimensions:48mm * 25mm * 14mm (L * W * H)

Module Properties: non-isolated step-up module (BOOST) 65 * 36.5 * 23 (length * width * high) (mm) Input voltage:10-32V Output voltage: 12-35V (adjustable) Output Current: 5A (MAX) Input Current: 10A (MAX) (Please enhance heat dissipation if more than 10A) Output power: natural cooling 100W (MAX), enhance heat dissipation 150W (MAX) Easy to drive 65W 90W dual-core notebook. Use a 12V battery drive 19V 3.42A notebook, the module temperature about 45c Conversion efficiency: 94% (measured at Input 16V, output 19V 2.5A) Output Ripple: 2% (MAX) 20M-bandwidth Operating Temperature: Industrial (-40c to +85c) (ambient temperature exceeds 40c, lower power use, or to enhance heat dissipation) Full load temperature rise: 45c No-load current: 25mA typical Voltage regulation: 0.5% Dynamic response speed: 5% 200uS Short circuit protection: None (Please Install fuses and protection circuits at Input port.) Input Reverse Polarity Protection: None (Please Series diode at the input port.)Some Applications: 1. DIY an output adjustable vehicle power supply, connect the 12V input, and output could be 14-35V(adjustable freely), However, the output voltage can not be less than the input voltage. 2. Car laptop power supply: connected to 12V power supply, output voltage regulation as your notebook need.

Module based on:TP4056 The module can manage battery charging and discharging, and also has built in boost converter to boost the voltage to match load conditions Charging voltage: 4.2V DC Charging current: Max. 1A Discharging current: Max. 2A Input voltage: 4.5-8V DC Output voltage: 4.3-27V DC (Continuously adjustable) Size: 3.3x2.3cm/1.3x0.91"

DESCRIPTION SPECS GENERAL Packaged Quantity1 Embedded SecurityTrusted Platform Module (TPM 1.2) Security Chip Operating SystemWindows 8.1 Pro 64-bit Edition ManufacturerHP PROCESSOR / CHIPSET CPUIntel Celeron N2840 / 2.16 GHz Max Turbo Speed2.58 GHz Number of CoresDual-Core CacheL2 - 2 MB 64-bit ComputingYes FeaturesIntel Burst Technology CACHE MEMORY TypeL2 cache Installed Size1 MB RAM Memory Speed1333 MHz Configuration Featuresprovided memory is soldered TechnologyDDR3L SDRAM Installed Size2 GB MEMORY TechnologyDDR3L SDRAM Speed1333 MHz DISPLAY LCD Backlight TechnologyWLED backlight Widescreen DisplayYes Monitor FeaturesHD standard-viewing angle (SVA) anti-glare TypeLED Diagonal Size (metric)29.5 cm Display Resolution AbbreviationHD AUDIO & VIDEO Graphics ProcessorIntel HD Graphics Integrated WebcamYes SoundStereo speakers, two microphones Featuresnoise-cancellation technology HARD DRIVE TypeSSD SSD Form FactoreMMC Capacity32 GB INPUT TypeClickPad, keyboard Featuresmulti-touch touchpad COMMUNICATIONS Wireless Protocol802.11b/g/n, Bluetooth 4.0 Wireless ControllerBroadcom BCM43142 PROCESSOR CPU TypeCeleron Processor NumberN2840 ManufacturerIntel Clock Speed2.16 GHz CARD READER Typecard reader Supported Flash MemorySD Memory Card, SDHC Memory Card, SDXC Memory Card BATTERY Capacity37 Wh Cells3-cell Technologylithium ion Run Time (Up To)6.25 hour(s) AC ADAPTER InputAC 120/230 V (50/60 Hz) Output45 Watt CONNECTIONS & EXPANSION InterfacesHDMIHeadphone/microphone combo jackUSB 3.0USB 2.0 Memory Card ReaderYes (SD Card, SDHC Card, SDXC Card) HEADER BrandHP Product LineHP Stream Model11 Pro LocalizationEnglish Country KitsUnited States Packaged Quantity1 CompatibilityPC NETWORKING Data Link ProtocolBluetooth 4.0, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n Wireless NICBroadcom BCM43142 MISCELLANEOUS SecurityTrusted Platform Module (TPM 1.2) Security Chip Featuresfanless, security lock slot (cable lock sold separately) Included Accessoriespower adapter Manufacturer Selling ProgramHP Smart Buy MONITOR Diagonal Size11.6 in SYSTEM Notebook Typethin and light PlatformWindows Hard Drive Capacity32 GB Embedded SecurityTrusted Platform Module (TPM 1.2) Security Chip DIMENSIONS & WEIGHT Width11.8 in Depth8.1 in Height0.8 in AUDIO OUTPUT Compliant StandardsDTS Studio Sound MANUFACTURER WARRANTY Type1 year warranty ENVIRONMENTAL STANDARDS ENERGY STAR CertifiedYes PHYSICAL CHARACTERISTICS Weight2.82 lbs OPERATING SYSTEM / SOFTWARE OS Provided: TypeWindows 8.1 Pro 64-bit Edition TypeHP Support Assistant, HP Utility Center, OneDrive VIDEO OUTPUT Graphics ProcessorIntel HD Graphics Graphics Processor SeriesIntel HD Graphics NOTEBOOK CAMERA Integrated WebcamYes SERVICE & SUPPORT Type1 Month warranty SERVICE & SUPPORT DETAILS Typelimited warranty Service Includedparts and labor Full Contract Period1 Month GENERAL ManufacturerHP Specifications of HP Stream 11 Pro - 11.6" LED Display - Intel Celeron N2840 - 2 GB RAM - 32 GB eMMC - Win 10 - (Refurbished) BrandHPSKU222856653_PK-1439637739Display SizeBelow 32 Inches Memory Type 1Storage Speed1Battery Type1No. of Battery Cells1Backlit KeyboardNoNo. of USB 2.0 PortsNULLNo. of USB 3.0 Ports2Input Output portsHDMINo. of USB 3.1 PortsNULLAC AdapterYesNo. of HDMI Ports1No. of VGA PortsNULLGraphic CardIntelCard Reader2-in-1Dimensions1ProcessorIntelHard Disk (GB)32CPU Speed (GHz)2-3GHzOperating SystemWindows 10Screen Resolution1Graphics Memory2 GB What’s in the box Laptop - Charger - Power Cable Mention that you found this ad on DealMarkaz.pk when you call.

The range of w1209 digital temperature controller is -50 to 110C. Resolution of temperature module at -9.9 to 99.9 is 0.1C The resolution of the module at all other temperatures is 1C. The accuracy of the measurement of the W1209 Temperature Control Switch is 0.1 C. Its control accuracy is 0.1C. The module refresh rate is 0.5 Sec. The power controlling module input power is 12V. NTC is its measuring inputs. Its output consists of 1 channel relay and its capacity is 10A.

ASUS PROART Z690-CREATOR WIFI MB LGA 1700 ATX motherboard Price in Pakistan CPU Supports Intel® 10 nm CPU Supports Intel® Turbo Boost Technology 2.0 and Intel® Turbo Boost Max Technology 3.0** * Refer to www.asus.com for CPU support list. ** Intel® Turbo Boost Max Technology 3.0 support depends on the CPU types. Chipset Z690 Memory 4 x DIMM, Max. 128GB, DDR5 6000(OC)/ 5800(OC)/ 5600(OC)/ 5400(OC)/ 5200(OC)/ 5000(OC)/ 4800MT/s Non-ECC, Un-buffered Memory* Dual Channel Memory Architecture Supports Intel® Extreme Memory Profile (XMP) OptiMem II * Refer to www.asus.com for the Memory QVL (Qualified Vendors Lists), and memory frequency support depends on the CPU types. Graphics 1 x HDMI® port** 2 x Intel® Thunderbolt™ 4 ports (USB Type-C®) support DisplayPort*** and Thunderbolt™ video outputs**** * Graphics specifications may vary between CPU types. Please refer to www.intel.com for any updates. ** Support [email protected] as specified in HDMI 2.1. *** Support [email protected] as specified in DisplayPort 1.4. **** Output at TBT4_E1 and TBT4_E2, the USB Type-C® ports right under RJ45 ports, each requires a USB-C to DisplayPort adapter cable. VGA resolution support depends on processors' or graphic cards' resolution. Expansion Slots Intel® 12th Gen Processors* 2 x PCIe 5.0/4.0/3.0 x16 slot(s) (supports x16 or x8/x8 mode(s)) Intel® Z690 Chipset** 1 x PCIe 3.0 x16 slot (supports x4 mode) * Supports PCIe bandwidth bifurcation for RAID on CPU function, please refer to PCIe bifurcation & M.2 setting in PCIe x16 slot (from CPU) table on support site. ** Supports Intel® Optane Memory H Series on PCH-attached PCIE slot Storage Supports 4 x M.2 slots and 8 x SATA 6Gb/s ports Intel® 12th Gen Processors M.2_1 slot (Key M), type 2242/2260/2280/22110 - Intel® 12th Gen processors support PCIe 4.0 x4 mode. Intel® Z690 Chipset** M.2_2 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode) M.2_3 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0 x4 mode) M.2_4 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 & SATA modes)*** 8 x SATA 6Gb/s ports*** * Intel® Rapid Storage Technology supports NVMe RAID 0/1/5, SATA RAID 0/1/5/10. ** Intel® Rapid Storage Technology supports Intel® Optane Memory H Series on PCH attached M.2 slots. *** M.2_4 slot shares bandwidth with SATA6G_5~8. SATA6G5~8 will be suspended once either a SATA or NVMe device is detected at M.2_4. Ethernet 1 x Intel® 2.5Gb Ethernet 1 x Marvell® 10Gb Ethernet ASUS LANGuard Wireless & Bluetooth Intel® Wi-Fi 6E Wi-Fi 6E 2x2 Wi-Fi 6E (802.11 a/b/g/n/ac/ax) Supports 2.4/5/6GHz frequency band* Bluetooth v5.2 hardware ready** * WiFi 6E 6GHz regulatory may vary between countries, and function will be ready in Windows 11 or later. ** Bluetooth v5.2 function will be ready in Windows 11 or later. USB Rear USB:Total 8 ports 2 x Thunderbolt™ 4 port(s) (2 x USB Type-C®) with up to 5V/3A, 15W charging support 6 x USB 3.2 Gen 2 port(s) (6 x Type-A) 1 x USB 3.2 Gen 2x2 connector(s) (support(s) USB Type-C® with 60W PD/QC4+) 1 x USB 3.2 Gen 1 header(s) support(s) additional 2 USB 3.2 Gen 1 ports 2 x USB 2.0 header(s) support(s) additional 4 USB 2.0 ports Audio Realtek S1220A 7.1 Surround Sound High Definition Audio CODEC* - Impedance sense for front and rear headphone outputs - Internal audio Amplifier to enhance the highest quality sound for headphone and speakers - Supports: Jack-detection, Multi-streaming, Front Panel Jack-retasking - High quality 120 dB SNR stereo playback output and 113 dB SNR recording input (Line-in) - Supports up to 32-Bit/192 kHz playback*" Audio Features - Power pre-regulator reduces power input noise to ensure consistent performance - Premium Japanese audio capacitors - Dedicated audio PCB layers - Audio cover - Unique de-pop circuit * Due to limitations in HDA bandwidth, 32-Bit/192 kHz is not supported for 7.1 Surround Sound audio. ** A chassis with an HD audio module in the front panel is required to support 7.1 Surround Sound audio output. Back Panel I/O Ports 2 x Thunderbolt™ 4 USB Type-C® port(s) 6 x USB 3.2 Gen 2 port(s) (6 x Type-A) 2 x DisplayPort (Input only) 1 x HDMI® port 1 x ASUS Wi-Fi Module 1 x Marvell® AQtion 10Gb Ethernet port 1 x Intel® 2.5Gb Ethernet port 5 x Audio jacks 1 x BIOS FlashBack™ button Internal I/O Connectors Fan and Cooling related 1 x 4-pin CPU Fan header(s) 1 x 4-pin CPU OPT Fan header(s) 1 x 4-pin AIO Pump header(s) 5 x 4-pin Chassis Fan header(s) Power related 1 x 24-pin Main Power connector 1 x 8-pin +12V Power connector 1 x 4-pin +12V Power connector Storage related 4 x M.2 slots (Key M) 8 x SATA 6Gb/s ports USB 1 x USB 3.2 Gen 2x2 (support(s) USB Type-C®) 1 x USB 3.2 Gen 1 header(s) support(s) additional 2 USB 3.2 Gen 1 ports 2 x USB 2.0 header(s) support(s) additional 4 USB 2.0 ports Miscellaneous 3 x Addressable Gen 2 header(s) 1 x AURA RGB header(s) 1 x Clear CMOS header 1 x COM Port header 1 x CPU Over Voltage jumper 1 x Front Panel Audio header (AAFP) 1 x M.2 slot (Key E) 1 x Speaker header 1 x SPI TPM header (14-1pin) 1 x 20-3 pin System Panel header with Chassis intrude function 1 x RTC Battery header 1 x Thermal Sensor header Special Features ASUS 5X PROTECTION III - DIGI+ VRM (- Digital power design with DrMOS) - Enhanced DRAM Overcurrent Protection - ESD Guards - LANGuard - Overvoltage Protection - SafeSlot - Stainless-Steel Back I/O ASUS Q-Design - M.2 Q-Latch - Q-Connector - Q-DIMM - Q-LED (CPU [red], DRAM [yellow], VGA [white], Boot Device [yellow green]) - Q-Slot ASUS Thermal Solution - M.2 heatsink - VRM heatsink design ASUS EZ DIY - BIOS FlashBack™ button - BIOS FlashBack™ LED - Box Headers - ProCool II - Pre-mounted I/O shield AURA Sync - AURA RGB header(s) - Addressable Gen 2 header(s) Software Features ASUS Exclusive Software Armoury Crate - AURA Creator - AURA Sync - Fan Xpert 4 - Two-Way AI Noise Cancelation AI Suite 3 - 5-Way Optimization with AI Overclocking TPU EPU DIGI+ VRM Fan Xpert 4 Turbo app ASUS CPU-Z IT Management software supported - ASUS Control Center Express(ACCE) ProArt Creator Hub CreationFirst MyAsus Norton Anti-virus software (Free Trial version) WinRAR UEFI BIOS AI Overclocking Guide ASUS EZ DIY - ASUS CrashFree BIOS 3 - ASUS EZ Flash 3 - ASUS UEFI BIOS EZ Mode FlexKey BIOS 256 Mb Form Factor ATX 30.5cm*24.5cm

DESCRIPTION 40W Laser Module Effect Output Power 40W Output Optical Power 5W Electric Power 12V 1.8A(1.5A-2A) Focus Length 45mm Cable 3PIN 80CM Function Engraving/Cutting Application laser engraver/laser cutter Material Aluminum alloy Module Size 40*40*141.4 mm Fan Speed 10000rpm Operating Temp 0~60℃ Interface XH2.54-3P socket Driver Protection Surge protection over voltage protection Power Adjustable Support 5V PWM modulation Weight 240g Wavelength 450mm Lahore, Kahna Nau, Lahore, Punjab, Pakistan

DESCRIPTION Input voltage: 2V ~ 24V Output voltage: Up to 28V Efficiency: ~93% On board preset: Adjust Output Voltage (Multi Turns 20 Turns) Input voltage: should not exceed the maximum input voltage Peak current: output current should not more than 2A Output voltage: should always be higher than Input voltage PCB Size: 30 mm * 17 mm * 14 mm Method Of Use: The module of the IN+ and – after 2~24v, IN adjusting the potentiometer can adjust output voltage, output voltage is greater than the input voltage. Mention that you found this ad on DealMarkaz.pk when you call.

HCSR04 Ultrasonic module 4PIN Module main technical parameters: 1.Working Voltage : 5V(DC) 2.Static current: Less than 2mA. 3.Output signal: Electric frequency signal, high level 5V, low level 0V. 4.Sensor angle: Not more than 15 degrees. 5.Detection distance: 2cm-450cm. for complete spec visit our web site http://www.matrixelectronic.com/Development-tools/distance-sensor-module/ULTRASONIC-MODULE Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com