Motorcycle lithium protection board

Module name: 3S 12.6V Li-ion Lithium Battery 18650 Charger Protection Board Suitable range: For nominal voltage 3.6V 3.7V lithium battery(Including 18650,26650, lithium polymer batteries) Charging voltage: 12.6V Maximum output current: 20A Maximum output power / charging power: 252W Color: green material: plastic Product size:59*20*3.4mm Product weight: 4.4g Package Contents: 1 PCS x 3 string 12.6V 20A 18650 lithium battery protection board Precautions: 1.Strictly according to the diagram wiring: 0V/4.2V/8.4V/12.6V,Otherwise it will cause damage to the chip. 2.After connection,it need to first charge activation, then will have the output.

Size: approx.50x16x1mm Maximum discharge current: 10A Overcharge detection voltage: 4.25-4.35V±0.05V Over-discharge detection voltage: 2.3-3.0V±0.05V Maximum working current: 5A-8A Transient current: 9A-10A Operating temperature: -40~50? Storage temperature: -40~80? Quiescent current: <6uA Internal resistance: <60mO Service life: >30,000 hours

Product Name: 3 string 12.6V 40A lithium battery protection board Charging voltage: DC 12.6V~13.6V Continuous discharge current: 40A maximum (if the heat dissipation environment is not good, please reduce the load current) Continuous charging current: up to 20A Balance Version Product size: 41*61*4mm Enhance Version Product size: 41*55*4mm Applicable choice: applicable to the nominal voltage of 3.7V, fully charged 4.2V lithium battery (including 18650, 26650, polymer lithium battery), can be drilled below 170W

What you receive: there are 20 pieces charg modules in our package, practical tools for you, which can also meet your various needs, enough for you to change and replace Details: the charg board inputs with micro-USB female, can be directly inputed to do with phone charger rechargeable, still retains the input voltage wiring pads, convenient for you to DIY; Charg cut-off voltage: 4.2V, max charge current: 1000 mA Function introduction: input voltage is 4.5V-5.5V, over-discharge protection voltage is 2.5V, over current protection current is 3A; Connect the to the B+ B-, inserted into the USB female mobile phone charger, the red light is being charged and the green light to full Suitable occasion: the charg board is applied for single-cell lithium or multi-cell parallel lithium charg, and the charg port can be ed from USB, which are convenient for you to operate

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / – 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / - 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.