Lithium battery charger protection board module

Module name: 3S 12.6V Li-ion Lithium Battery 18650 Charger Protection Board Suitable range: For nominal voltage 3.6V 3.7V lithium battery(Including 18650,26650, lithium polymer batteries) Charging voltage: 12.6V Maximum output current: 20A Maximum output power / charging power: 252W Color: green material: plastic Product size:59*20*3.4mm Product weight: 4.4g Package Contents: 1 PCS x 3 string 12.6V 20A 18650 lithium battery protection board Precautions: 1.Strictly according to the diagram wiring: 0V/4.2V/8.4V/12.6V,Otherwise it will cause damage to the chip. 2.After connection,it need to first charge activation, then will have the output.

Size: approx.50x16x1mm Maximum discharge current: 10A Overcharge detection voltage: 4.25-4.35V±0.05V Over-discharge detection voltage: 2.3-3.0V±0.05V Maximum working current: 5A-8A Transient current: 9A-10A Operating temperature: -40~50? Storage temperature: -40~80? Quiescent current: <6uA Internal resistance: <60mO Service life: >30,000 hours

Product Name: 3 string 12.6V 40A lithium battery protection board Charging voltage: DC 12.6V~13.6V Continuous discharge current: 40A maximum (if the heat dissipation environment is not good, please reduce the load current) Continuous charging current: up to 20A Balance Version Product size: 41*61*4mm Enhance Version Product size: 41*55*4mm Applicable choice: applicable to the nominal voltage of 3.7V, fully charged 4.2V lithium battery (including 18650, 26650, polymer lithium battery), can be drilled below 170W

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / – 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

100% New and High Quality Micro USB TP4056 Dual Charging Module Input Voltage: 4.35V - 6V (recommended voltage 5v) Chargingcut-off Voltage: 4.2V (± 1%) Maximum Charging Current Output: 1000mA (1A) Battery Discharge Protection Voltage: 3.0V Charging Status LEDs:Red LED Charging, Green LED Fully Charged Note: The installation and usgae of these modules require some basic knowledge of electronics, if you dont know how to install, please don't buy it.

Manage the constant current to constant voltage charging of a connected lithium battery Over-discharge protection - keeps your battery from being discharged below 2.4V, a healthy minimum voltage level for your batteryIf a connected battery has been discharged below 2.4V the module will cut output power from the battery until the battery voltage has been re-charged above 3.0V (the over-discharge release voltage), which at that time the module will again allow discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows charging of the battery to occur through the parasitic diode of the discharge control MOSFET (FS8205A Dual MOSFET). Overcharge protection - the module will safely charge your battery to 4.2V Overcurrent and short-circuit protection - the module will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs Soft-start protection limits inrush current Trickle charge (battery reconditioning) - if the voltage level of the connected battery is less than 2.9V, the module will use a trickle charge current of 130mA until the battery voltage reaches 2.9V, at which point the charge current will be linearly increased to the configured charge current.

DESCRIPTION Features: This is the mobile power module Accessories, 18650 Circuit board shell. Meet the individual needs of your DIY, but you must understand basic electronic assembly. Motherboard comes with protection function: Charging overcharge protection, over-discharge protection, overcurrent protection. Intelligent output device after charging full, automatically stop charging, to prevent mobile phones overcharge. Output voltage and current stable, will not harm user devices. Specifications: Micro USB input: 5V 1A USB Output: 5V 2.1A / 5V 1A(Dual USB interface) Charging display: intelligent digital display Batteries Type: liquid lithium-ion batteries (18650) Product Size: 57mm x 28mm Screen size:27mm x 17mm Installation instructions: The circuit board is connected to the battery negative B-, B + is the positive, do not connecting reversed, connecting reversed will burn the board, the battery is connected in parallel welding, assembling battery. Note that the insulation between the battery and the circuit board, battery lead not to touch the circuit board, so as not to cause a short circuit. Package included: 1 x Mobile Power Bank 18650 Battery Charger PCB Mention that you found this ad on DealMarkaz.pk when you call.

The input voltage: 4.35-6 v (recommended voltage 5 v) Charge cut-off voltage: 4.2 V + / - 1% Maximum charging current output: 1000 ma The battery overcharge protection voltage: 4.28 V Battery overcharge lifting voltage: 4.00 V The battery discharge protection voltage: 3.0 V Battery discharge termination voltage: 3.2 V Battery: over-current protection current 3 a The board size: about 2.5 * 1.65 CM Light state: no load the light not bright, red light for recharging, is full of green light.

What you receive: there are 20 pieces charg modules in our package, practical tools for you, which can also meet your various needs, enough for you to change and replace Details: the charg board inputs with micro-USB female, can be directly inputed to do with phone charger rechargeable, still retains the input voltage wiring pads, convenient for you to DIY; Charg cut-off voltage: 4.2V, max charge current: 1000 mA Function introduction: input voltage is 4.5V-5.5V, over-discharge protection voltage is 2.5V, over current protection current is 3A; Connect the to the B+ B-, inserted into the USB female mobile phone charger, the red light is being charged and the green light to full Suitable occasion: the charg board is applied for single-cell lithium or multi-cell parallel lithium charg, and the charg port can be ed from USB, which are convenient for you to operate