Feedback

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CUD Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CUD Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Digital Acoustic Feedback Suppression The digital acoustic feedback suppression facility automatically eliminates acoustic feedback (also known as 'howling' or 'Larsen effect'). This gives better speech intelligibility by allowing the speaker volume to be turned up as loud as required without any risk of feedback. Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room• Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment• Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

Description: Details iShopping.pk brings you the best price for Bosch CCS-CU Control Unit For CCS 900 Ultro Conference System U.S. Version with express shipping all over Pakistan.   The Bosch CCS-CU Control Unit is the central power and control station for all CCS 900 Ultro Conference System contributor units, such as the chairman and delegate units. The control unit will supply power for up to 50 delegate / chairman units, and provide control for up to 150. The unit features a built in speaker and automated, programmable control over contributor units without the need for an operator. Its Digital Acoustic Feedback Suppression (DAFS) eliminates feedback howling and maintains clear, intelligible speech. Plenty of connections allow for interfacing within paging systems, amplifier systems, recording devices and more. The unit is feature rich, however its control section is straightforward and intuitive to operate in any conference setting.   Features: Discussion Control Without Operator The CU can be setup to operate standalone without the need for an operator. The following 5 modes can be chosen using a rotary control on the unit's top panel: • Open mode - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active • Open mode with auto-switch-off - allows selection of one to four microphones (excluded chairmen microphones) which can be simultaneously active. If the delegate does not speak for 30 seconds, microphones are automatically switched off • Override mode - delegates can override each other simply by activating their microphones. Only one microphone can be active at any one time. (Note: In override mode, delegates cannot override chairmen) • Chairman only mode - only chairmen can speak. Delegate microphones cannot be activated, even when a chairman is not speaking • Test mode - checks if system connections are correct. All microphone light rings and contribution unit LEDs light up to indicate that units are properly connected Supplies Power for up to 50 Contribution Units The CU has two trunk outputs for the loop-through connection of contribution units. It is possible to connect 25 contribution units to each trunk output, with a maximum system cable length of 109.3 yards (100m). Provides Control for up to 150 Contribution Units Up to 3 CUs can be used together in a discussion system to power and control a maximum of 150 contribution units. In this configuration a single CU acts as a master controller for the entire system. Built-in Monitor Loudspeaker The built-in monitor loudspeaker and headphone socket allow the conference to be monitored. Interfaces the System With External Equipment The following equipment can be interfaced to the CCS Ultro Discussion System through the CU: • External wired or wireless microphone - for guest speakers or audience participation. (Note: The external microphone is muted when the priority button on a chairman unit is pressed, and when the system is operating in 'chairman only' mode) • External PA system - for transmitting the proceedings to an audience in the same room or an adjacent room • Tape recorder - for external recording and playing back meetings and discussions • Audio equipment - for providing background music • Telephone coupler - to allow a remote delegate to participate via telephone• External audio processing - an insertion connector is provided Controls and Indicators (Top) • Mains on/off switch • Graphical display for status information (CCS‐CURD) • 5 soft buttons for configuration and control of thebuilt-in MP3 recorder (CCS‐CURD) • Loudspeaker volume control, for setting output level of loudspeakers of contribution units. This control also determines the maximum level for the headphone outputs of the contribution units and the CU. • Microphone mode rotary switch, for setting the number of simultaneously active microphones, and selecting one of the four operation modes (plus test mode) • Power on LED Controls and Indicators (Back) • On/off switch for digital acoustic feedback suppression facility (CCS‐CUD, CCS‐CURD)• Microphone input gain adjustment • External recorder input gain adjustment • Insertion connector bypass switch   Specifications: Connections Top • 1x 0.14" (3.5mm) stereo headphone socket Back • 1x AC input • 2x 7-pole circular female connectors, trunk in/out loop through interconnection  • 1x 3-pole female XLR connector, microphone input (can be used as line input by included 50dB attenuator) • 1 x Cinch connector pair, line input/output  • 1 x Cinch connector pair, telephone input/output • 1 x Cinch connector pair, insertion input/output  • 2 x Cinch connector pairs (R/L channel), external recorder input/output • USB interface (CCS-CURD) Power Supply Mains voltage: 100 to 240 VAC ± 10% Current consumption: maximum 0.9A (100 VAC) to 0.3 A (240 VAC) DC supply to contribution units: 24V ± 1V (current limited) Volume mute (50dB att.) + 10 steps of 1.9dB Limiter 10dB above nominal level loudspeaker / headphone Gain Gain reduction due to number of open microphones (NOM): ÷ NOM ± 1 dB Total Harmonic Distortion Nominal input (85 dB SPL): Max. input (110 dB SPL): Sample Rate Recording: 32kHz Playback: 32, 44.1, 48kHz Bit Rate Recording: 64, 96, 128, 192, 256 KBit/sec Playback: any bitrate Mount Tabletop (portable or fixed) 19-inch rack flush mounting Material Top: polymer Bottom: painted metal Color Charcoal and Black Dimensions (HxWxD) 3.4 x 14.2 x 5.6" (84 x 361 x 143mm) Height of feet: 0.22" (5.5mm) Weight 3.3 lb (1.5kg)

FEEL THE FUTURE OF RACING Meet the next generation of racing wheels. The award-winning Logitech G design is re-engineered to dial into your game physics, delivering unprecedented realism. Feel the pistons pumping, the gravel crunching, and every shift, drift, and hairpin turn like never before. NEXT-GEN SIMULATION Our latest innovation in force feedback technology connects directly to in-game simulation engines and physics to produce higher fidelity, real-time responses. The feedback frequency range is also increased for dramatically improved detail and realism compared to previous generations. CLOSED-LOOP MOTOR CONTROL The right current means the right torque. G923’s advanced firmware monitors all the current flowing through the wheel motors, continuously adjusting voltage to match outputs from game physics. By going beyond default settings, G923 delivers pinpoint accuracy and unprecedented realism. MORE TRACTION. LESS SMOKE. Get off the starting line cleaner and faster with a programmable dual-clutch launch assist in supported games. CRAFTED FOR RACING The classic design—modernized. The new colourway, premium brushed metal, automotive-style leather stitching, and polished pedals give G923 a professional finish. Form follows function with an integrated centre marker and rotary dial. ON-WHEEL GAME CONTROLS Complete Xbox One or PS4 controls are built right into the steering wheel. No matter how you race, every command is directly at hand. 24-POINT SELECTION DIAL Traction, torque, brake force—it’s all adjustable from an integrated dial that you control. PROGRESSIVE BRAKE PEDAL More responsive, more accurate. The progressive spring mimics the performance of a pressure-sensitive brake system for a real racing experience. Reposition the pedal faces for heel-toe manoeuvres and even more control. BUILT-IN REV INDICATOR Built-in coloured LEDs show your RPM range in supported games. See when you’re redline-ing—right in your line of sight. CUSTOMISE WITH G HUB Take full control of your rig. Adjust wheel sensitivity, force feedback levels, and button customization via powerful G HUB Gaming Software for PC. Custom-build multiple profiles for any game and application.

  The definitive sim racing wheel for PlayStation 4 and PlayStation 3: Realistic steering and pedal action for the latest racing titles Built to last: Durable solid steel ball bearings, stainless steel shifter and pedals and hand-stitched leather wheel grip Dual-motor force feedback: Realistically simulates the racing experience with smooth, quiet helical gearing Easy-access game controls: On-wheel D-pad, console buttons, paddle shifters and LED indicator lights. Responsive floor pedal unit: Accelerate, brake and change gears with the feel of an actual car Platform compatibility: PlayStation 4 / PlayStation 3 and games that support Logitech force feedback racing wheel, OR Windows 8, 8.1, or Windows 7, 150 MB of available hard disk space, USB port, games that support Logitech force feedback racing wheel

Outemu Blue Switch: Switch Type: Clicky Switch Operating Force: 60 gf/cN End Operating Force: 65 gf/cN MAX Pre Travel: 2.20mm Total Travel: 4.00mm Descriptions: The characteristic of this tactile switch is featured by tactile and audible feedback. Thanks to the striking /"click/", the Outemu Blue Switch not only provides noticeable, but also acoustic feedback. Outemu Red Switch: Switch Type: Linear Switch Operating Force: 45 gf/cN End Operating Force: 65 gf/cN MAX Pre Travel: 2.00mm Total Travel: 4.00mm Descriptions: The linear switching characteristic combined with the low spring resistance triggers directly. The Outemu Red Switch is the first choice for beginners in the world of mechanical keyboards.The smooth-running enables balanced writing and gaming sessions. Outemu Brown Switch: Switch Type: Tactile Switch Operating Force: 50 gf/cN End Operating Force: 65 gf/cN MAX Pre Travel: 2.00mm Total Travel: 4.00mm Descriptions: The characteristic of this tactile switch is characterized by a noticeable feedback. The noiseless guidance of the Outemu Brown Switch trains the sure instinct and helps to act tactically and strategically. Outemu Black Switch: Switch Type: Linear Switch Operating Force: 60 gf/cN End Operating Force: 80 gf/cN MAX Pre Travel: 2.00mm Total Travel: 4.00mm Descriptions: The linear switching characteristic combined with an increased spring force triggers directly. Thanks to a stronger spiral spring, the tried and true Outemu Black Switch smoothly moves the keys back to the starting position and grants the necessary staying power for long writing and gaming sessions.

Description: Details iShopping.pk brings you the best price for Yamaha 12 Input Powered Digital Stereo Mixer (EMX7)   with 1 year official warranty and express shipping all over Pakistan.   Specifications: Analog Input Characteristics Input Connectors Channels 1-4: 4x Combo XLR-1/4" / 6.35 mm Channels 5/6: 1x XLR, 2x 1/4" / 6.35 mm Channels 7/8: 1x XLR, 2x 1/4" / 6.35 mm Channels 9/10: 1x XLR, 2x RCA  Channels 11/12: 1x XLR, 2x RCA, 1x 1/8" / 3.5 mm stereo mini-jack Load Impedance Channels 1-4 (XLR Mic/Line): 3 kOhms actual, 50-600 Ohms nominal with mics Channels 1-4 (1/4" Mic/Line): 8 kOhms, 600 Ohms nominal with lines Channel 4 (1/4", Hi-Z Engaged): 1 MOhms actual, 10 kOhms lines nominal Channels 5-12 (XLR): 2 kOhms actual, 50 - 600 Ohms mics nominal Channels 5-12 (1/4", RCA, 1/8"): 10 kOhms actual, 600 Ohms lines nominal Input Level Sensitivity Channel 1-4 (XLR, Mic): -60 dBu (0.775 mV) Channel 1-4 (XLR, Line): -30 dBu (24.5 mV) Channel 1-4 (1/4", Mic): -50 dBu (2.45 mV) Channel 1-4 (1/4", Line): -20 dBu (77.5 mV) Channel 4 (Hi-Z Engaged, Mic): -50 dBu (2.45 mV) Channel 4 (Hi-Z Engaged, Line): -20 dBu (77.5 mV) Channels 5-12 (XLR): -60 dBu (0.775 mV) Channels 5-8 (1/4"): -20 dBu (77.5 mV) Channels 9-12 (RCA, 1/8"): -8 dBu (316 mV) Nominal Channel 1-4 (XLR, Mic): -43 dBu (5.48 mV) Channel 1-4 (XLR, Line): -13 dBu (173 mV) Channel 1-4 (1/4", Mic): -33 dBu (17.3 mV) Channel 1-4 (1/4", Line): -3 dBu (548 mV) Channel 4 (Hi-Z Engaged, Mic): -33 dBu (17.3 mV) Channel 4 (Hi-Z Engaged, Line): -3 dBu (548 mV) Channels 5-12 (XLR): -43 dBu (5.48 mV) Channels 5-12 (1/4", RCA, 1/8"): -3 dBu (548 mV) Maximum Before Clip Channel 1-4 (XLR, Mic): -15 dBu (138 mV) Channel 1-4 (XLR, Line): +15 dBu (4.36 V) Channel 1-4 (1/4", Mic): -5 dBu (436 mV) Channel 1-4 (1/4", Line): +25 dBu (13.8 V) Channel 4 (Hi-Z Engaged, Mic): -5 dBu (436 mV) Channel 4 (Hi-Z Engaged, Line): +20 dBu (7.75 V) Channels 5-12 (XLR): -15 dBu (138 mV) Channels 5-12 (1/4", RCA, 1/8"): +25 dBu (13.8 V) Analog Output Characteristic Output Connectors Stereo Out (L/R): 2x 1/4" / 6.35 mm balanced Aux Sends (1/2): 2x 1/4" / 6.35 mm balanced Rec Out (L/R): 2x RCA unbalanced Impedance Stereo Out (L/R): 600 Ohms actual, 10 kOhms Lines Aux Sends (1/2): 600 Ohms actual, 10 kOhms Lines Rec Out (L/R): 600 Ohms actual, 10 kOhms Lines Output Level Stereo Out (L/R): +4 dBu (1.228 V) nominal, +20 dBu (7.75 V) max before clipping Aux Sends (1/2): +4 dBu (1.228 V) nominal, +20 dBu (7.75 V) max before clipping Rec Out (L/R): -10 dBV (0.308 V) nominal, +18 dBV (7.75 V) max before clipping Loudspeaker Outputs Connectors Speakers A/B: 2x Neutrik speakON NL4, 1/4" / 6.35 mm Impedance Actual Source Impedance: For Use with Nominal: 4 Ohm speakers, 8 Ohm speakers Output Level 4 Ohm Speakers: 600 W (1 Hz THD+N 8 Ohm Speakers: 400 W (1 Hz THD+N General Specifications Output Power 1 kHz THD+N 1 kHz THD+N Frequency Response Frequency Response Refer to the nominal output level @ 1 kHz Input to Speakers: +1/-3 dB (40 Hz to 20 kHz) Input to Stereo Out, Aux 1/2 Send: +0.5/-1.0 dB (20 Hz to 20 kHz) THD + N Input to Speakers (Mic/Line): 0.1% @ 10 W (40 Hz to 20 kHz) Input to Speakers (Line - Channels 1-4) 0.04% @ 65 W (1 kHz) Input to Stereo Out, Aux 1/2 Send (Mic/Line): 0.02% @ +14 dBu (20 Hz to 20 kHz)  Input to Stereo Out, Aux 1/2 Send (Line - Channels 1-4): 0.007% @ +20 dBu (1 kHz) Hum & Noise EIN: -117 dBu Residual Output Noise Input to Speakers: -70 dBu (40 Hz to 20 kHz, Stereo Master Level: min) Input to Stereo Out, Aux 1/2 Sends: -82 dBu (20 Hz to 20 kHz, Stereo Master Level: min) Crosstalk (1 kHz): -85 dB Input Channels Mono (Mic/Line): 8 Stereo: (Line): 4 Total: 12 Output Channels Speakers: A/B Aux 1 Send Aux 2 Send Stereo Out: L/R Rec Out: L/R Bus Stereo: 1 Aux: 2 (including FX) Pad Channels 1-4: 30 dB Hi-Z Input Channel 4: Supported HPF High Pass Filter (Channels 1-3): 80 Hz, -12 dB/octave EQ Section High: 10 kHz +15/-15 dB Mid: 2.5 kHz +15/-15 dB Low: 100 Hz +15/-15 dB Compressor Single knob compressor Audio Level Meter 2x 12 Points LED Meter: (-30, -25, -20, -15, -10, -6, -3, 0, +3, +6, +10, Peak) Built-in Effects SPX Algorithm: 24 programs Output Channel Function Graphic EQ Speaker Processor  Feedback Suppressor Phantom Power +48 V Footswitch Input Effect mute on/off Protection Load Protection: DC-fault Amplifier Protection: Overheat protection, overcurrent protection, integral power protection Power Supply Protection: Overheat protection, overcurrent protection Power Power Requirements: 100-240 VAC, 50/60 Hz Power Consumption: 45 W (Idle) / 250 W (1/8 power) Operating Temperature 32 to 104°F / 0 to 40°C     The  Yamaha EMX7  is a 12-input powered mixer with an integrated 1420W amplifier, eight mic/line inputs, four stereo line inputs, and two Aux sends. The mixer features a Hi-Z guitar input on channel four and each channel offers a 3-band EQ for custom tailoring your sound. Channels 1-4 offer XLR-1/4" combo jacks. Channels 5 through 12 provide mono XLR inputs, with channels 5-8 offering 1/4" inputs and 9-12 offering an additional set of stereo RCA inputs. Channels 11/12 also include an 1/8" stereo mini-jack for connecting portable music players. The EMX7 includes a single knob compressor on channels 1-4, an integrated feedback suppressor, and a built-in multi-effects processor with SPX series algorithms. Additionally, the mixer offers an integrated speaker processor with bass boost, designed to bring out the best quality from Yamaha or 3rd party passive speakers. The EMX7 also includes a Flex9GEQ graphic equalizer for Aux 1, Aux 2, and Stereo Output. The Flex9GEQ allows you to select up to nine bands out of a total of 31 and adjust the gain. 

Description: Details iShopping.pk brings you the best price for Yamaha 12 Input Powered Digital Stereo Mixer (EMX5)   with 1 year official warranty and express shipping all over Pakistan.   Specifications: Input Connectors Channels 1-4: 4x Combo XLR-1/4" / 6.35 mm Channels 5/6: 1x XLR, 2x 1/4" / 6.35 mm Channels 7/8: 1x XLR, 2x 1/4" / 6.35 mm Channels 9/10: 1x XLR, 2x RCA  Channels 11/12: 1x XLR, 2x RCA, 1x 1/8" / 3.5 mm stereo mini-jack Load Impedance Channels 1-4 (XLR Mic/Line): 3 kOhms actual, 50-600 Ohms nominal with mics Channels 1-4 (1/4" Mic/Line): 8 kOhms, 600 Ohms line Channel 4 (1/4", Hi-Z Engaged): 1 MOhms actual, 10 kOhms lines nominal Channels 5-12 (XLR): 2 kOhms actual, 50 - 600 Ohms lines nominal Channels 5-12 (1/4", RCA, 1/8"): 10 kOhms actual, 600 Ohms nominal Input Level Sensitivity Channel 1-4 (XLR, Mic): -60 dBu (0.775 mV) Channel 1-4 (XLR, Line): -30 dBu (24.5 mV) Channel 1-4 (1/4", Mic): -50 dBu (2.45 mV) Channel 1-4 (1/4", Line): -20 dBu (77.5 mV) Channel 4 (Hi-Z Engaged, Mic): -50 dBu (2.45 mV) Channel 4 (Hi-Z Engaged, Line): -20 dBu (77.5 mV) Channels 5-12 (XLR): -60 dBu (0.775 mV) Channels 5-8 (1/4"): -20 dBu (77.5 mV) Channels 9-12 (RCA, 1/8"): -8 dBu (316 mV) Nominal Channel 1-4 (XLR, Mic): -43 dBu (5.48 mV) Channel 1-4 (XLR, Line): -13 dBu (173 mV) Channel 1-4 (1/4", Mic): -33 dBu (17.3 mV) Channel 1-4 (1/4", Line): -3 dBu (548 mV) Channel 4 (Hi-Z Engaged, Mic): -33 dBu (17.3 mV) Channel 4 (Hi-Z Engaged, Line): -3 dBu (548 mV) Channels 5-12 (XLR): -43 dBu (5.48 mV) Channels 5-12 (1/4", RCA, 1/8"): -3 dBu (548 mV) Maximum Before Clip Channel 1-4 (XLR, Mic): -15 dBu (138 mV) Channel 1-4 (XLR, Line): +15 dBu (4.36 V) Channel 1-4 (1/4", Mic): -5 dBu (436 mV) Channel 1-4 (1/4", Line): +25 dBu (13.8 V) Channel 4 (Hi-Z Engaged, Mic): -5 dBu (436 mV) Channel 4 (Hi-Z Engaged, Line): +20 dBu (7.75 V) Channels 5-12 (XLR): -15 dBu (138 mV) Channels 5-12 (1/4", RCA, 1/8"): +25 dBu (13.8 V) Analog Output Characteristic Output Connectors Stereo Out (L/R): 2x 1/4" / 6.35 mm balanced Aux Sends (1/2): 2x 1/4" / 6.35 mm balanced Rec Out (L/R): 2x RCA unbalanced Impedance Stereo Out (L/R): 600 Ohms actual, 10 kOhms Lines Aux Sends (1/2): 600 Ohms actual, 10 kOhms Lines Rec Out (L/R): 600 Ohms actual, 10 kOhms Lines Output Level Stereo Out (L/R): +4 dBu (1.228 V) nominal, +20 dBu (7.75 V) max before clipping Aux Sends (1/2): +4 dBu (1.228 V) nominal, +20 dBu (7.75 V) max before clipping Rec Out (L/R): -10 dBV (0.308 V) nominal, +18 dBV (7.75 V) max before clipping Loudspeaker Outputs Connectors Speakers A/B: Neutrik speakON NL4, 1/4" / 6.35 mm phone jack Impedance Actual Source Impedance: For Use with Nominal: 4 Ohm speakers, 8 Ohm speakers Output Level 4 Ohm Speakers: 500 W (1 Hz THD+N 8 Ohm Speakers: 370 W (1 Hz THD+N General Specifications Output Power 1 kHz THD+N 1 kHz THD+N Frequency Response Frequency Response Refer to the nominal output level @ 1 kHz Input to Speakers: +1/-3 dB (40 Hz to 20 kHz) Input to Stereo Out, Aux 1/2 Send: +0.5/-1.0 dB (20 Hz to 20 kHz) THD + N Input to Speakers: 0.1% @ 10 W (40 Hz to 20 kHz), 0.05% @ 50 W (1 kHz) Input to Stereo Out, Aux 1/2 Send: 0.03% @ +14 dBu (20 Hz to 20 kHz), 0.007% @ +20 dBu (1 kHz) Crosstalk (1 kHz): -85 dB Input Channels Mono (Mic/Line): 8 Stereo: (Line): 4 Total: 12 Output Channels Speakers: A/B Aux 1 Send Aux 2 Send Stereo Out: L/R Rec Out: L/R Bus Stereo: 1 Aux: 2 (including FX) Pad Channels 1-4: 30 dB Hi-Z Input Channel 4: Supported HPF High Pass Filter (Channels 1-3): 80 Hz, -12 dB/octave EQ Section High: 10 kHz +15/-15 dB Mid: 2.5 kHz +15/-15 dB Low: 100 Hz +15/-15 dB Compressor Single knob compressor Audio Level Meter 7 points (-20, -10, -6, 0, +6, +10, Peak) Built-in Effects SPX Algorithm: 24 programs Output Channel Function Master EQ (Speech to Music) Monitor EQ  Feedback Suppressor Phantom Power +48 V Footswitch Input Effect mute on/off Protection Load Protection: DC-fault Amplifier Protection: Overheat protection, overcurrent protection, integral power protection Power Supply Protection: Overheat protection, overcurrent protection Power Power Requirements: 100-240 VAC, 50/60 Hz Power Consumption: 42 W (Idle) / 210 W (1/8 power) Operating Temperature 32 to 104°F / 0 to 40°C   The  Yamaha EMX 5  is a 12-input powered mixer with an integrated 1260W amplifier, eight mic/line inputs, four stereo line inputs, and two Aux sends. The mixer features a Hi-Z guitar input on channel four and each channel offers a 3-band EQ for custom tailoring your sound. Channels 1-4 offer XLR-1/4" combo jacks. Channels 5 through 12 provide mono XLR inputs, with channels 5-8 offering 1/4" inputs and 9-12 offering an additional set of stereo RCA inputs. Channels 11/12 also include an 1/8" stereo mini-jack for connecting portable music players. The EMX 5 includes a single knob compressor on channels 1-4, an integrated feedback suppressor, and a built-in multi-effects processor with SPX series algorithms. Additionally, the mixer offers a Master EQ, which provides a single knob to control the level of low end. At the far left, the speech setting cuts low frequencies, while the middle position is neutral for music playback. The far right setting provides a Bass Boost to enhance music playback.

Description: Details iShopping.pk brings you the best price for Toa Electronics 14.49" Microphone Conference System (TS-773) with express shipping all over Pakistan.   The Toa TS-773 Unidirectional Microphone is designed for use with the TS-771 chairman and TS-772 delegate stations. The microphone provides easy positioning and transparent reproduction of speech. An LED ring indicator illuminates when the microphone is in use. The unidirectional polar pattern minimizes off-axis noise and feedback.   Features: Unidirectional Polar Pattern The unidirectional polar pattern provides a generous pick up area while minimizing off-axis noise and feedback. Speech Indicator LED A speech indicator LED illuminates while the microphone is in use.   Specifications: Transducer Electret Condenser Polar Pattern Unidirectional Frequency Range 100Hz to 13kHz Impedance 1.8kΩ Output Connector 4-pin XLR Length 14.49 (368mm) Weight 3.17 oz (90g)

Description: Details iShopping.pk brings you the best price for Toa Electronics 20.39" Microphone Conference System (TS-774) with express shipping all over Pakistan.   The Toa TS-774 Unidirectional Microphone is designed for use with the TS-771 chairman and TS-772 delegate stations. The microphone provides easy positioning and transparent reproduction of speech. An LED ring indicator illuminates when the microphone is in use. The unidirectional polar pattern minimizes off-axis noise and feedback.   Features: Unidirectional Polar Pattern The unidirectional polar pattern provides a generous pick up area while minimizing off-axis noise and feedback. Speech Indicator LED A speech indicator LED illuminates while the microphone is in use.   Specifications: Transducer Electret Condenser Polar Pattern Unidirectional Frequency Range 100Hz to 13kHz Impedance 1.8k ohms Output Connector 4-pin XLR Length 20.39 (518mm) Weight 3.7 oz (105g)

Description: Details iShopping.pk brings you the best price for ClearOne Converge Pro 2 128 DSP Mixer with express shipping all over Pakistan.   The Converge Pro 2 128 DSP Mixer with 12 Mic/Line Inputs from ClearOne is a 1 RU digital audio processor for conferences and sound reinforcement. Signal processing has been upgraded to offer world-beating echo cancellation, adaptive noise reduction, and advanced feedback suppression in speech applications for boardrooms, conference rooms, lecture halls, training rooms, courtrooms, houses of worship, and more. Smaller conference rooms can use a single Converge Pro 2 processor. It is ideal for connecting up to three Beamforming Microphone Arrays and up to three DIALOG 20 dual-wireless microphones (sold separately). All these devices use a single P-Link peripheral connection up to 200' apart. Additional line inputs and podium microphones can be connected into the 12 mic/line inputs. Additionally, a USB port connects your computer, which allows you to connect to any standard conferencing platforms, including ClearOne Spontania.   Features: • 12 Mic/Line inputs with AEC • Built-in USB for Windows-based conferencing • Adaptive ambient noise cancellation with DARE feedback elimination • Advanced microphone gating • Dialer app for Windows, Mac, iOS, Android tabletop controller with touch panel • Control from wall, web, or third party connection   Specifications: Mic/Line Inputs 12 Line Outputs 8 USB Connects to your computer for industry standard conferencing platforms Ethernet Yes RS232 Connection Yes GPIO Yes P-Link Connector 2 x P-link C-Link Connector 2 x C-link Dimensions Not specified by manufacturer Weight Not specified by manufacturer

Description: Details iShopping.pk brings you the best price for Razer BlackWidow Lite Silent Mechanical Gaming Keyboard - Black with express shipping all over Pakistan.   Details: Razer BlackWidow Lite Black Edition Silent mechanical gaming keyboard with compact form factor The Razer BlackWidow Lite delivers full functionality in a compact form. Featuring Razer Mechanical Switches (Orange) with included o-rings for extra sound dampening, experience silent but tactile feedback. The keyboard is also equipped with individually backlit keys with full brightness control. Use Razer Synapse 3, a cloud-based hardware configuration tool, to access advanced options like assigning macros, setting shortcuts, and more. Razer Mechanical Switches Designed for gaming with the highest performance, Razer Mechanical Switches (Orange) are silent while producing tactile feedback—perfect for typing so you know when every key is pressed. The switches also provide optimized actuation and reset points for responsiveness, with new side walls for increased stability and protection against dust and liquids. Silent keys with included o-rings Enjoy the tactile feeling of mechanical switches without fear of being too loud. The Razer BlackWidow Lite comes with o-rings to further dampen the sound of your already silent keys, reducing key travel distance at the same time to alleviate typing fatigue. Compact form The Razer BlackWidow Lite provides essential control in a compact form. The detachable cable also makes it easy to pack and take along if you’re always on the go. Individually backlit keys With global white LED backlighting, you can always find the right key, even in dark settings. Control how bright you need it to be instantly or turn it off when you don’t need it. Razer Synapse 3 Get access to advanced options and granular control with Razer Synapse 3, a cloud-based hardware configuration tool that lets you assign macros, set shortcuts, and more. Engineered for durability Razer Mechanical Switches deliver top performance and durability to make sure you’re ahead of your game. The switches are manufactured in-house to ensure strict requirements are met for each switch produced, resulting in a life span of up to 80 million key strokes.

Logitech G813 LIGHTSYNC RGB Mechanical Gaming Keyboard Price in Pakistan THE NEXT DIMENSION Advanced gaming technologies in a sophisticated ultra-thin design. Fully customizable, equipped with LIGHTSYNC RGB and dedicated G-keys. Engineered for high-performance gameplay with low-profile GL mechanical switches in clicky, tactile, and linear variations. Experience G813 and play the next dimension. LIGHTSYNC  INTELLIGENT RGB LOW PROFILE  MECHANICAL GAMING SWITCHES ULTRA THIN  22 MM TOTAL HEIGHT   IMPOSSIBLY THIN G815 is a feat of engineering and design with an incredibly refined, impossibly thin build with no compromises on performance or feature set. Durable, comfortable and ready for intense gaming sessions, G815 is truly the next generation of gaming mechanical keyboards.   ADVANCED LOW-PROFILE MECHANICAL Get the speed, accuracy and performance at half the height of traditional switches. Low-profile GL mechanical switches are rigorously tested to meet strict endurance, responsiveness, and accuracy requirements. Available in three switch types: GL Clicky - audible click and tactile feedback GL Tactile - a gentle bump for some tactile feedback GL Linear - a completely smooth keystroke   LIGHTSYNC RGB G813 is fully customizable per key across ~ 16.8M colors. Create your own animations or choose from a selection of preset effects. With LIGHTSYNC technology, lighting is driven by games, audio, or your screen to deliver the most immersive RGB experience ever. Unify a theme, enhance your gameplay, and extend your gaming setup through your keyboard.   ENDLESS CONTROL Sleek and sophisticated G815 offers a focused, high-performance experience with every feature you need to take total control—like programmable G-keys and onboard profiles. Make G815 the command center for your PC.     USB PASSTHROUGH Connect and power more devices with convenience and speed. An additional dedicated USB cable connects the USB passthrough port on the back of the keyboard for full-power throughput and data speed. Plug in and charge your device or plug in a mouse to charge your adversaries without missing a beat.     DEDICATED MEDIA CONTROLS Onboard media controls are right at your fingertips. Dedicated controls quickly adjust volume, play/pause and skip music or videos, and mute audio instantly.     PACKAGE CONTENTS G813 LIGHTSYNC RGB mechanical keyboard User documentation   PHYSICAL SPECIFICATIONS Length: 475 mm Width: 150 mm Height: 22 mm Weight (w/o cable): 1045 g Weight (w/cable): 1145 g PC Cable Length: 1.8 m   TECHNICAL SPECIFICATIONS Low Profile GL Switches: Actuation distance: 1.5 mm Actuation force: 45 g Total travel distance: 3.0 mm   Onboard Memory: 2 Lighting Profiles 3 G-keys Macro Profiles   Other Features: LIGHTSYNC RGB, per key lighting 5 Dedicated G-Keys Dedicated media control and edgeless volume wheel   REQUIREMENTS Windows ®  7 or later macOS ®  10.11 or later 2x USB ports (1x keyboard, 1x USB passthrough port) (Optional) Internet access for Logitech G HUB software 4 Advanced features require Logitech G HUB Gaming Software, available for download at logitechg.com/GHUB   PART NUMBER

THE NEXT DIMENSION A breakthrough in design and engineering, the G915 features LIGHTSPEED pro-grade wireless, advanced LIGHTSYNC RGB, and new high-performance low-profile mechanical switches. Meticulously crafted from premium materials, the G915 is a sophisticated design of unparalleled beauty, strength, and performance. Meet G915 LIGHTSPEED and play the next dimension. LIGHTSPEEDPRO-GRADE WIRELESS LOW PROFILE MECHANICAL GAMING SWITCHES 22MM ULTRA THINGROUND BREAKING DESIGN     LIGHTSPEED WIRELESS G915 features pro-grade LIGHTSPEED wireless that achieves super-fast 1 ms performance. It’s the same wireless technology that esports pros all over the world trust in competitions. G915 is also fully functional when plugged in via USB, so you can charge and play simultaneously.     IMPOSSIBLY THIN G915 is a feat of engineering and design. Meticulously crafted from premium materials, G915 is incredibly refined, impossibly thin, and built with a no-compromises commitment to performance and feature set. Durable, comfortable, and ready for intense gaming sessions, G915 is truly the next generation of gaming mechanical keyboards. ADVANCED LOW-PROFILE MECHANICAL G915 is our first keyboard to feature new, high performance low-profile GL mechanical switches that provide all the speed, accuracy, and performance of traditional switches—at half the height. Our GL switches are rigorously tested to meet strict endurance, responsiveness, and accuracy requirements. Available in three switch types: GL Clicky  - audible click and tactile feedback GL Tactile  - a gentle bump for some tactile feedback GL Linear  - a completely smooth keystroke LIGHTSYNC RGB G915 offers intelligent LIGHTSYNC RGB technology which enables fully customizable per-key lighting across ~ 16.8 M colors. Create your own animations or choose from a selection of preset effects for the most immersive RGB experience. Unify a theme, enhance your gameplay, and extend your gaming setup through your keyboard. 1 Advanced features require Logitech G HUB Gaming Software, available for download at logitechg.com/GHUB ENDLESS CONTROL Sleek and sophisticated G915 offers a focused, high-performance experience with every feature you need to take total control—like programmable G-keys and onboard profiles. Make G915 the command center for your PC. 2 Advanced features require Logitech G HUB Gaming Software, available for download at logitechg.com/GHUB REMARKABLE BATTERY LIFE Enjoy hours of non-stop game time on a single charge. Battery indicator light on the keyboard and Logitech G HUB will notify you when you’re at 15 percent battery. Fully recharges in just three hours. Keep playing while it’s plugged in and charging via micro USB. CONNECT TO MULTIPLE DEVICES Connect to LIGHTSPEED wireless for super-fast 1 ms connection or switch to another device with the push of a button using  Bluetooth ®  connectivity. Toggle between high-performance LIGHTSPEED wireless via USB receiver and  Bluetooth  quickly and easily. DEDICATED MEDIA CONTROLS Onboard media controls are right at your fingertips. Dedicated controls quickly adjust volume, play/pause and skip music or videos, and mute audio instantly.

PLAY THE NEXT DIMENSION A breakthrough in design and engineering, now in black and white colorways. G915 TKL features LIGHTSPEED pro-grade wireless, advanced LIGHTSYNC RGB, and high-performance low-profile mechanical switches. Meticulously crafted from premium materials, the G915 TKL is a sophisticated design of unparalleled beauty, strength, and performance, now in an even more compact form factor. G915 TKL. Play the next dimension.     LIGHTSPEEDPRO-GRADE WIRELESS LOW PROFILE MECHANICAL GAMING SWITCHES TENKEYLESS368 MM COMPACT WIDTH     COMPACT TENKEYLESS DESIGN G915 TKL features the same advanced technologies as the G915—but in a more compact design, providing more room for mouse movement. The USB receiver can be stored in the back of the keyboard for additional portability. LIGHTSPEED WIRELESS G915 TKL features pro-grade LIGHTSPEED wireless that achieves super-fast 1 ms performance. G915 TKL is also fully functional when plugged in via USB, so you can charge and play simultaneously. IMPOSSIBLY THIN G915 TKL is a feat of engineering and design. It’s incredibly refined, impossibly thin, and built with a no-compromise commitment to performance and feature set. Durable, comfortable, and ready for intense gaming sessions, G915 TKL is truly the next generation of gaming mechanical keyboards. ADVANCED LOW-PROFILE MECHANICAL SWITCHES G915 TKL features high-performance low-profile GL mechanical switches that provide all the speed, accuracy, and performance of traditional switches—at half the height. Our GL switches are rigorously tested to meet strict endurance, responsiveness, and accuracy requirements. White colorway comes in GL Tactile and the black colorway comes in three 1 White colorway only available in GL Tactile switch type  switch types: GL Clicky  - audible click and tactile feedback GL Tactile  - a gentle bump for some tactile feedback GL Linear  - a completely smooth keystroke LIGHTSYNC RGB G915 TKL offers intelligent LIGHTSYNC RGB technology which enables fully customizable per-key lighting across ~ 16.8 M colors. Create your own animations or choose from a selection of preset effects for the most immersive RGB experience. Unify a theme, enhance your gameplay, and extend your gaming setup through your keyboard. 2 Advanced features require Logitech G HUB Gaming Software, available for download at logitechg.com/GHUB ENDLESS CONTROL Sleek and sophisticated G915 TKL offers a focused, high-performance experience with every feature you need to take total control—like onboard profiles and game mode. 3 Advanced features require Logitech G HUB Gaming Software, available for download at logitechg.com/GHUB  Make G915 TKL the command center for your PC. REMARKABLE BATTERY LIFE Enjoy hours of non-stop game time on a single charge. Battery indicator light on the keyboard and Logitech G HUB will notify you when the battery is low. Fully recharges in under four hours. Keep playing while it’s plugged in and charging via micro USB. CONNECT TO MULTIPLE DEVICES Connect to LIGHTSPEED wireless for super-fast 1 ms connection or switch to another device with the push of a button using  Bluetooth®   connectivity. Toggle between high-performance LIGHTSPEED wireless via USB receiver and  Bluetooth  quickly and easily. DEDICATED MEDIA CONTROLS Onboard media controls are right at your fingertips. Dedicated controls quickly adjust volume, play/pause and skip music or videos, and mute audio instantly.

Multi-Key Rollover Centered Backlight Design 1000Hz Report Rate Screw Enhanced Space-Bar Anti-Slippery Lift MECHA-LIKE SWITCH Innovative patented Mecha-Like Switch is derived from LK(Light Strike) Switch’s Mechanism, it provides the clicky  tactile feedback of mechanical key press on a comfortable, soft cushioned rubber dome. It provides about 95% similar typing experience as typing on LK switch mechanical keyboard. 5-ZONE NEON BACKLIGHT Glow with 7-color backlight, illuminate your gaming vibes and bring your game to the next level! Centered Backlight Design LED emits through the center of each key emitting evenly through each key. 1ms Key Response Instantaneous execution is guaranteed with the 1000Hz ultrapolling technology, giving you a response time of ultra-fast 1ms. Dependable Durability Electronically sealed circuits are paired with drainage paths for a stronger durability to splashes and spills. Game Mode Press Fn+F8 will disable "Window" keys to avoid interruption during the game session. 1000 Hz Report Rate 1000 Hz full report rate provides faster and timely feedback. Anti-Slippery Keyboard Lift Anti-slippery lift prevents keyboard from moving or vibrating during game session. Elite Bloody KeyDominator Software Create your own macro keys with the Bloody KeyDominator software available for downloads at bloody.com

Product Description           COLOR    GALLERY   Multi-Key Rollover   Centered Backlight Design   1000Hz Report Rate   Screw Enhanced Space-Bar   Anti-Slippery Lift   MECHA-LIKE SWITCH Innovative patented Mecha-Like Switch is derived from LK(Light Strike) Switch’s Mechanism, it provides the clicky  tactile feedback of mechanical key press on a comfortable, soft cushioned rubber dome. It provides about 95% similar typing experience as typing on LK switch mechanical keyboard. 5-ZONE NEON BACKLIGHT Glow with 7-color backlight, illuminate your gaming vibes and bring your game to the next level! Centered Backlight Design LED emits through the center of each key emitting evenly through each key. 1ms Key Response Instantaneous execution is guaranteed with the 1000Hz ultrapolling technology, giving you a response time of ultra-fast 1ms. Dependable Durability Electronically sealed circuits are paired with drainage paths for a stronger durability to splashes and spills. Game Mode Press Fn+F8 will disable "Window" keys to avoid interruption during the game session. 1000 Hz Report Rate 1000 Hz full report rate provides faster and timely feedback. Anti-Slippery Keyboard Lift Anti-slippery lift prevents keyboard from moving or vibrating during game session. Elite Bloody KeyDominator Software Create your own macro keys with the Bloody KeyDominator software available for downloads at bloody.com.   TECH SPECS PERFORMANCE PERFORMANCE Report Rate: 1000Hz Backlit：Neon Water-Resistant：Double Secured Space-Bar: Screw Enhanced Connector: USB Cable Length: 1.8m Windows 7/ 8 / 8.1 / 10 PRODUCT SIZE

Spigen iphone 13 Pro Max Mag Armor Magsafe Case– Matte Black Price in Pakistan Description iPhone 13 Pro Max Mag Armor MagSafe Case is a  Magnet integrated shock absorption TPU case with  Raised lip to protects screen and camera &  Tactile buttons for solid feedback and an easy press with  Air Cushion Technology for shock absorption. Magnet integrated shock absorption TPU case Raised lip to protects screen and camera Tactile buttons for solid feedback and an easy press Air Cushion Technology for shock absorption iPhone 13 Pro Max Case Compatible with iPhone 13 Pro Max (2021) Check other items for iPhone 13 Pro max

Spigen iPhone 13 Pro Max Ultra Hybrid Mag Magsafe – Graphite Price in Pakistan Description iPhone 13 Pro Max Ultra Hybrid Mag Magsafe Enabled Case is a  Magnet integrated shock absorption clear PC back case with  Raised lip to protects screen and camera &  Tactile buttons for solid feedback and an easy press. Magnet integrated shock absorption clear PC back case Raised lip to protects screen and camera Tactile buttons for solid feedback and an easy press Air Cushion Technology for shock absorption iPhone 13 Pro Max Case Compatible with iPhone 13 Pro Max (2021) Check other items for iPhone 13 Pro max

Spigen iPhone 13 Pro Max Ultra Hybrid Mag Magsafe – White Price in Pakistan Description iPhone 13 Pro Max Ultra Hybrid Mag Magsafe Enabled Case is a  Magnet integrated shock absorption clear PC back case with  Raised lip to protects screen and camera &  Tactile buttons for solid feedback and an easy press. Magnet integrated shock absorption clear PC back case Raised lip to protects screen and camera Tactile buttons for solid feedback and an easy press Air Cushion Technology for shock absorption iPhone 13 Pro Max Case Compatible with iPhone 13 Pro Max (2021) Check other items for iPhone 13 Pro max

DESCRIPTION About this item Haptic feedback - Feel physically responsive feedback to your in-game actions with dual actuators which replace traditional rumble motors. In your hands, these dynamic vibrations can simulate the feeling of everything from environments to the recoil of different weapons. Adaptive triggers - Experience varying levels of force and tension as you interact with your in-game gear and environments. From pulling back an increasingly tight bowstring to hitting the brakes on a speeding car, feel physically connected to your on-screen actions. Built-in microphone and headset jack - Chat with friends online using the built-in microphone or by connecting a headset to the 3.5mm jack. Easily switch voice capture on and off at a moment’s notice with the dedicated mute button. Internet and account for PlayStation Network required. DualSense Controller PS5 and PC compatible. Not compatible with PS4. PS Remote Play requires Remote Play App connected to Wi-Fi, PS4 or PS5 console with the latest system software and compatible game. A PS4 or PS5 console with a wired connection via a LAN cable is recommended. Version 4.0 of the Remote Play App on iOS and iPadOS or version 4.1 on macOS is required for games to be playable with the controller over Bluetooth. Devices with macOS 11.3, iOS 14.5, iPadOS 14.5 or tvOS 14.5 or later supported. Cable not included. To connect or charge the controller use the USB cable supplied with the PS5 console. Controllers sold separately. Mention that you found this ad on DealMarkaz.pk when you call.

Mind Merge Data Recovery was started in 2004 by some IT experts with the vision to help not only businesses, and government organizations, but individuals and families who had lost their precious data. https://mindmergepk.com With continues development and investment in research and development, Mind Merge Data Recovery is able to offer state of the art, professional and cost effective data recovery services in Pakistan. With our customer feedback system, you always know what's going on and when to expect your data recovered. Mind Merge Data Recovery Services first opened its office in Faisalabad and looking to extend its collection point to be opened across the Pakistan. Mind Merge Data Recovery is proud to be the first data recovery company in Pakistan offering RAID Data Recovery from almost all types of Arrays. Our company offers efficient, high-quality data recovery to keep the government running and people working. We also work with families and individuals, so no one has to suffer the trauma of permanent data loss. We know exactly what’s at stake, whether it is sensitive business documents or once in a lifetime memories caught on film. Mind Merge Data Recovery is the only place to find fast recovery at affordable prices.

We are continually looking to improve the TalkTalk website and would be grateful for your feedback once you have completed your visit. Your views are important to us and the survey will only take a maximum of 10 minutes to complete. When you leave the site the survey will automatically be presented to you. URL :http://www.talktalk.co.uk

Zebra incorporated extensive customer feedback, as well as the legacy of our industry leading Stripe and S4M printers, to create the new ZT200 Series family of printers with elegant space saving design, effortless setup, intuitive user operation, and ease of service and maintenance. Features USB Yes Serial Port Yes Parallel Port Yes Display Screen Type LCD Product Type Direct Thermal Printer Manufacturer Part Number ZT23042-D01100FZ Manufacturer Zebra Technologies Corporation Product Model ZT230 Product Name ZT230 Industrial Printer Brand Name Zebra Media Thickness 10 mil Media Type Continuous Label Media Type Die-cut Label Media Type Notch Media Type Black Mark Product Series ZT200 Maximum Label Width 4.50 Maximum Label Length 39 Standard Memory 128 MB Package Contents ZT230 Industrial Printer Power Cord with US Plug

Zebra incorporated extensive customer feedback, as well as the legacy of our industry leading Stripe and S4M printers, to create the new ZT200 Series family of printers with elegant space saving design, effortless setup, intuitive user operation, and ease of service and maintenance. General Information Manufacturer Part Number ZT22042-D01000FZ Manufacturer Website Address www.zebra.com Manufacturer Zebra Technologies Corporation Product Model ZT220 Product Name ZT220 Industrial Printer Product Series ZT200 Brand Name Zebra IO Expansions Media Types Handling Media Thickness 10 mil Maximum Roll Diameter 8 Media Type Continuous Label Media Sensor Transmissive Media Sensor Label Core Size 3 Maximum Label Width 4.50 Maximum Label Length 39 Memory Flash Memory 128 MB Standard Memory 128 MB Memory Technology DRAM Miscellaneous Package Contents ZT220 Industrial Printer Power Cord with US Plug

A website is the best important necessity for any business in current aggressive environment. No matter what kind of business you are present, your website is the coolest and the best way to interact with your clients. This is the most effective and cheapest way to promote your business. Mounting a website that characterizes you or your business is a seriousjob. There are numerousstandards where your website has to perform. Therefore, when you look for a web design and development company you would always want to choose from the best of best. You would also want to have one stop service for all web design and development related task. The awesome Features You’ll Loveincludes: • Web Hosting + Domain name Registration ( with .com, .net, .org) • Unlimited Pages • Picture Gallery • Feedback, Contact Us and Get a quote form • Social Media Links • Logo designing • Banner Designing • Add Designing • Online Chat Support Why us ? • Responsive Design ( Run on all mobile devices) Covered Areas Books, Clothing, Shoes, Gift Items, Furniture, Medicines, Jewelry, Textile Items, Shoes, Pizza Takeaways, Toys, Stationary, Boutique, Auto Dealers and lot of others we can help you and serve you Contuct us: Ph: 92-321-8591513 Landline: 92-61-6221155

Ideal for long-range deployments, the Ubiquiti UAP-AC-LR UniFi AC1300 simultaneous dual-band WiFi PoE access point offers simultaneous, dual-band operation with 3x3 MIMO in the 2.4 GHz band and 2x2 MIMO in the 5 GHz band. The innovative antenna design provides a long-range, symmetrical-link coverage area, and the antenna gain of this Ubiquiti UAP-AC-LR UniFi AC1300 AP performs better than one-way, high transmit power does for connecting distant clients. It is available in single, triple and five-packs, and can be configured with or without a hassle-free hosted cloud controller. Key Features Designed for Optimal RF Performance - The newly redesigned UniFi Controller optimises RF performance: Spectral Analysis - Collects feedback on full 5GHz and 2.4GHz WiFi channel interference Band Steering: Pushes connected WiFi clients to faster interference-free 5GHz channels. Airtime Fairness: Minimises problem-client effects on system performance by limiting their airtime access Powerful Hardware- Features the latest in WiFi 802.11AC MIMO technology with WiFi speeds up to 1300Mbps (450Mbps + 867Mbps) Includes UK Power Cable - No need to purchase additional cable for use in the United Kingdom, 1.8m IEC C5 cable included Google Maps Integration - Upload your own custom coverage maps or configure your map using the built-in Google Maps API. L3 Manageability - With L3 manageability, the UniFi Controller software can be run on a different subnet than the UniFi APs it manages, allowing 'no-touch' AP provisioning Multi-Site Management - A single UniFi Controller can manage multiple, distributed deployments and multi-tenancy for managed service providers. You can configure settings and administrator accounts specific to each deployment. One UniFied Network - Option to create one large wireless network across multiple APs that lets users move around the network wirelessly. Events and Alerts - UniFi makes it easy to view and set up email delivery of alerts and recent event notifications on your network(s). Access Points (APs) - Easily install, configure, and manage all access points from one location. Guest Portal/Hotspot Support - Easy customisation and advanced options for Guest Portals include authentication, Hotspot setup options, and the ability to run as an external portal server. Take advantage of UniFi's rate limiting for your Guest Portal and Hotspot package offerings. Apply different bandwidth rates (download/upload), limit total data usage, and limit duration of use. All UniFi AC APs include Hotspot functionality: Built-in support for billing integration using major credit cards via PayPal. Built-in support for voucher-based authentication. Built-in Hotspot Manager for voucher creation, guest management, and payment refund. Full customisation of Hotspot portal pages. Scalable enterprise WiFi management UniFi is the revolutionary WiFi system that combines enterprise performance, unlimited scalability, and a central management controller. The Ubiquiti UAP-AC-LR UniFi access points has a refined industrial design and can be easily installed using the included mounting hardware. Easily accessible through any standard web browser, the UniFi Controller software is a powerful software engine ideal for high-density client deployments requiring low latency and high uptime performance. Use the UniFi Controller software to quickly configure and administer an enterprise WiFi network – no special training required. RF map and performance features, real-time status, automatic UAP device detection, and advanced security options are all seamlessly integrated. http://dreamsnw.com/ Avalaible at Dreams Network & Technology (Pvt) Ltd. Contact: LHR: 04235784892 KHI: 02134710763, 02134711677, 02134721416

we are specialized in all fields of website development. We have experienced in Restaurant Website, textile website, factory website, packages website, Poultry website, Education website, Colleges website, Construction company website, Jobs website or any kind of . Our package includes  Domain Name registration  Hosting  Text contents writing  Complete analysis how to improve your business  Logo Creation or existing logo improvement  Add picture gallery  Add video gallery  Add in Google yahoo search engine  Place google map  Add social media connections  Client feedback form  Contact us form. For more information, please contact us nacseng@gmail.com or 0333-6156588

InCreate Technologies is providing cost effective biometric attendance machines and solutions for staff time management to large scale industries to small medium offices. We offers fingerprint reader, face recognition devices with complete after sale services and technical support. We provide high world-class solutions that optimize and secure your assets through the individual and collective expertise of our engineers. Our team work provides cost effective, intelligent solutions in a timely manner, in field of security works. ADVANTAGES: Intuitive system—requires no training Ergonomically friendly design Easy to understand user guidance by illumination and fully automatic image capture Instant quality check feedback to the user Auto Capture of left and right hands and both thumbs Auto Capture of all flats and rolled fingers Ultra lightweight and portable Provides a value-priced option, suitable for any office environment Water and dust protected housing.