Detection cards light

Overview The continuous casting vibration type ladle slag detection device is used to detect the slag content of the ladle nozzle in the steelmaking continuous casting process, so as to improve the cleanliness of the tundish molten steel and obtain the best yield of the ladle molten steel. The device adopts the principle of vibration detection. The LAG-S200 continuous casting ladle slag automatic detection system is developed by Wuhan CenterRise M&C Engineering Co., Ltd. after many years of research with many scientific research institutes, and fully combined with the actual situation on site. It has a real field application value as a continuous casting ladle slag automatic detection system. The meaning of the system 1. Reduce the amount of tundish slag 2. Improve the purity of molten steel 3. Improve the life of the tundish 4. Reduce sliding nozzle erosion 5. Reduce nozzle blockage 6. Increase continuous pouring heats 7. Reduce the amount of residual steel in the ladle when high-quality steel is casting 8. Improve the yield of molten steel 9. Improve the quality of continuous casting billets In order to improve the purity of the molten steel in the tundish, and improve the quality of the casting billet, especially to improve the quality of the billet in the transition section, and reduce the amount of residual steel in the high-quality ladle, and prolong the life of the tundish lining, and increase the continuous casting heats, it’s necessary to detect and control the slag in the later stage of continuous casting ladle casting. The working principle The LAG-S200 continuous casting ladle slag automatic monitoring system detects the slag state during the pouring process by receiving the vibration signal of the mechanical operating arm of the ladle nozzle. In the process of molten steel pouring, when molten steel flows through the long nozzle and pours into the tundish, the molten steel impacts the wall of the long nozzle and causes the vibration of the mechanical operating arm used to support the long nozzle. Since the specific gravity of the steelmaking slag is less than half of the specific gravity of the molten steel, it floats on the surface of the molten steel, and the steelmaking slag appears when the molten steel is about to be all poured. At this time, due to the high viscosity and poor fluidity of light steelmaking slag, the impact force of the mixed flow of molten steel and steel slag on the wall of the long nozzle is quite different from that of pure molten steel. The system mainly monitors the ladle slag of the continuous casting by measuring and analyzing the vibration difference of the mechanical operating arm. The vibration signal is connected to the operation control unit of the system control cabinet through the front-stage conditioning and amplification module through the sensor installed in the middle of the operating rod. After processing, it is output to the industrial computer for operation and analysis. The slag signal detected by the system is output from the system control cabinet to the front-end control unit, and then control the alarm horn and alarm light to work, or issue an instruction to close the ladle nozzle. The features of the system (1) It is easy to install, basically no modification is made to the field equipment, and the installation and debugging work will not affect the normal production of the enterprise. (2) The detection accuracy is high, and the effective rate is greater than or equal to 95%. The threshold of slag volume is accurately set, the output control function is powerful. It has excellent performance in technical indicators such as the sensor service life and sensor usage times. (3) The sensor is installed at a position far away from the molten steel, and is cooled by a special refrigeration device for 24 hours. The outer layer adopts a composite protection structure, which has a long service life. (4) Adopt professional and targeted signal processing methods to obtain the vibration characteristic parameters of the ladle slag, and analyze, reason and judge the effective slag signal through the vibration signal database, which has a high accuracy of slag alarm. (5) The architecture is established based on the artificial intelligence network, which has the functions of self-learning and self-induction. (6) The equipment adopts a modular design. The failure of each module will not affect other parts, which ensure more reliable operation of the system and easy maintenance. (7) The alarm display device is used on site to visually indicate the flow state of molten steel and slag. When slag carryover strats, we can choose automatic mode or manual mode. In both modes, the system will give audible and visual alarm signals to remind on-site operators. (8) The system has a powerful database function. Including the comparison function for last two ladles of casting time record, the system automatically stores the running data, and generates a record file every day. (9) The system has the function of automatically controlling the ladle nozzle. The control unit is an auxiliary system of the system, which is interconnected with the ladle slag detection system to automatically control the opening of the ladle nozzle and realize the whole-process control of the liquid level of the molten steel in the tundish. The composition of the system The LAG-S200 slag detection system consists of: vibration detection sensor, pre-signal amplifier, slag detection operation unit, tundish liquid level control unit, on-site operation indication box, and process control cabinet. 1. Vibration detection sensor: It is installed on the robotic arm of the stopper to detect the vibration signal of the whole casting process of the ladle. 2. Pre-signal amplifier: Amplify, convert and transmit the weak vibration signal detected by the vibration detection sensor. 3. Slag detection operation unit: Analyze, judge and discriminate the vibration signal to realize the discrimination of all steel, mixed slag and full slag , and output the slag alarm signal. 4. Tundish liquid level control unit: Accept the control signal of the tundish nozzle and the ladle nozzle, and realize automatic or manual control to the ladle slag according to the requirements. 5. On-site operation instruction box: Provides man-machine exchange for slag alarm indication, fault indication, system activation mode selection, and control mode selection. 6. Process control cabinet, providing power management, displaying man-machine interface and setting management. The parameters of the system 1. The system controls the slag inclusion in molten steel with high precision and closes the nozzle in real time. 2. Improve the quality of steel, reduce defective products, and improve the yield. 3. The yield of molten steel is increased by 0.3%-0.5%. The nozzle can be automatically closed, so that the disadvantage of untimely manual response is overcome and less molten steel remains in the ladle. The threshold value of molten steel (slag threshold) is set by the user within a wide range. 4. No artificial factors are involved, high reliability, good repeatability or consistency. 5. The steelmaking slag does not pass through or rarely flows into the tundish, which increases the service life of the refractory material and the sliding nozzle. 6. Reduce the blockage of the tundish nozzle and increase the number of continuous pouring heats of the tundish.

Dear Sir /Madam We have pleasure to inform you that the system is convenient, reliable and safest .it takes 3 to 5 hours to install the automatic system on your premises we provide 12 months compressive warranty on parts services and we have highly qualified staff ready for discussion and survey at your premises to guide you about your needs for automation & other system in your areas. Product Description: Stand Alone DVR4 & Its Cards We are proud to further expand our existing Standalone DVR product line with the addition of our DVR4 -Channel Embedded Linux Standalone DVR. This advanced remote viewable DVR is great for home or business camera installs DVR product line is our new DVR- 4 channel Standalone DVR. This DVR allows for recording/playback of up to 4 cameras on a single DVR and comes complete with enterprise grade features such as 4-channel loop back outputs, multi-location remote viewing, h.264 video encoding, embedded Linux operating system, PS2 mouse menu control, IR remote control, multi-user access and more. Even though the DVR- standalone dvr comes equipped with all of these features, it still manages to stay inside the budget standalone DVR making it a clear choice for larger home or business security camera system installations or even multi-location franchise remote viewing SPECIFICATIONS: • 4 CH, Stand Alone DVR DIY KIT • Hard Drive Storage 160GB • Video Compression Format MPEG4 • Adjustable Recording Speed Frame • Recording Modes • Manual/Time/Motion/Alarm/Remote • Motion Detect Sensitivity 4 adjustable variables • CD Manual and Hard Copy • DSUB pin Connector • Networking Solution Basic Functions: • 4 channel real time monitoring. • Each channel Image color can be adjusted independently by software. • Support insert 4 cards in the same PC at most, form 16 channel monitoring, and can also support mix inserting S9404 & S9808, to form 12 channel monitoring • Multi screen monitoring, 1,4,9,16,25, 36 split Screen available, support rotate display • Support multi-hard disks cycle recording • Recording both flow trends yard and fix yard are available • Intelligent searching for historical DVR files, up to 16 screen playback • Multi-user's authority management setup, support to set up user's operating authority • Support motion detection touch off the video recording, sending E-mail (monitoring pictures in the enclosure), sending alarm by phone, and by sound. • Setting up motion detection area discretionarily, the sensitivity is adjustable • Through IE realize such perfect network management functions as remote spot monitoring, remote historical playback, remote spot video recording, remote historical video recording. • Support Intranet IP to remote monitoring • Support one IE remote monitors several DVR of different IP. • Support one IE remote monitoring several different DVR within the same IP. • Support the watermark of the characters and time, the particular format of video files prevent being edited, the security is high. • The video file supports electron enlarge, taking pictures and instant print and exe format backup. • Support local and remote PTZ control Features: • High speed network transmission • High Image quality • Easy to installation and use GUI (Graphical User Interface) • Free Software upgradeable We enclose introduction brochures about for your review and we hope that the information will provide many of the answers to the questions you might have looking forward to your earlier response. Regards, EASY AUTOGATES 021-35163642

Overview： This product is a new type of mold copper plate surface detection equipment. The equipment adopts a high-precision and high-sensitivity laser ranging sensor, which scans the copper plate of the mould by scanning a laser line with a fixed width, and returns the measurement data in real time. After modeling and analyzing the data, the upper computer gives the wear data of the mold copper plate, as well as the data of surface cracks and surface flatness. The host computer software intuitively reflects the surface profile of the detected mold and thickness deviation and other data to the user in the form of data sheet, data curves and mold 3D model diagrams, providing a true and reliable theory for on-site operators to maintain the mold. The mold surface detection equipment is a high-precision instrument, which includes high-precision laser ranging sensors, two digital servomotors, encoders, horizontal sliding screws, vertical sliding screws, and calibration consoles, controllers and other components. The equipment has many advantages such as high accuracy, strong stability, convenient installation and strong observability. It is suitable for mold surface detection, surface flatness analysis, surface flaw detection, taper measurement, etc. It is also suitable for round billets, square billets, slabs, special-shaped billets, etc., widely used and powerful. The composition of the system： 1. The mold surface detection equipment is equipped with: data processing and display unit, horizontal motion mechanical power output unit, vertical mechanical power output unit, instrument motion control unit, laser measurement sensor, and instrument bracket. 2. Data processing and display unit: used for data acquisition and storage, system equipment control, parameter configuration, height display of the descent, start and stop control, etc. 3. Horizontal motion mechanical power output unit: the digital servo motor in the horizontal direction controls the sensor to move in the horizontal direction, so that the sensor can scan the horizontal inner cavity wall of the mold copper plate to detect data. 4. Vertical mechanical power output unit: the digital servo motor in the vertical direction controls the sensor to move in the vertical direction, so that the sensor can scan the vertical cavity wall of the mold copper plate to detect data. 5. Instrument motion control unit: It is used to control the motion scanning of the motor, and the running speed, running track, and control mode of the motor can be configured through parameter settings. 6. Laser measurement sensor: The laser displacement sensor adopts the principle of laser triangulation. The laser transmitter shoots the visible infrared laser to the surface of the measured object through the lens, and the laser reflected by the object passes through the receiver lens and is received by the internal line array image processing sensor. According to different distances, the corresponding positions of the light spots received on the line array sensor are also different. According to the angle of this reflection, the distance between the actual objects can be calculated by calculating the distance of the sensor spot. 7. Instrument bracket: The mold surface detection equipment need to be placed directly above the mold when it is in use, and it is required to be fixed firmly without displacement vibration during the measurement process to ensure the measurement accuracy. The parameters： Detection instrument service life: ≥5 years; Detection instrument reliability: more than 98%; Detection range: 60~1000mm (customizable) Detection accuracy: 0.01mm Spot diameter: 1.0x1.5mm (spot scan), 1.0x20mm (line scan) Falling pace: 1~20mm/step Single measurement time: less than 2min Power supply: DC24V Operating temperature: -20~80℃ Equipment warm-up time: 3~5min Shock resistance: 50G (X, Y, Z axis) Vibration resistance: 10Hz~5Hz (amplitude 1.5mm, each 2 hours in X, Y, Z axis)

Overview The infrared converter slag detection system uses a far-infrared thermal imager to monitor the situation of converter tapping in real time, and is connected to the main control computer in the electrical room through the conversion and transmission of video signals. The radiation intensity in the infrared wavelength range of 7-14um is different to distinguish molten steel and slag. In the later stage of the converter tapping, the molten steel gradually decreases, and the steelmaking slag is involved in the molten steel and flows out of the tapping hole. After the thermal imager recognizes the steelmaking slag in the imaging temperature measurement, it will give an alarm according to the slag content ratio threshold set by the software. The thermal imager will start the slide plate to close the tapping hole, so as to realize the control of the slag in the converter tapping, and ensure the maximum yield of molten steel and the minimum control of the steelmaking slag content. The effect of slag detection in converter tapping is of great significance to the control effect of the slag amount. The converter slag detection and control system developed by our company conducts non-contact monitoring of the tapping steel flow through the far-infrared detector thermal imager. It can detect the slag condition in real time and output an alarm signal and control system, which can replace manual visual inspection and provide accurate, efficient and stable slag detection effect. When the system finds the slag, the intelligent control unit quickly makes a judgment of lifting the furnace and blocking the slag and outputs an alarm signal. As shown in Figure 1, the system includes thermal imager, front purge protection box, front electrical box, power distribution cabinet, main control monitor, monitor of rocking furnace chamber, sound and light alarm, infrared converter slag monitoring software system, etc. The features of thermal imager 1. The temperature measurement range is 200°C ~ 2000°C, high temperature measurement accuracy, and multiple temperature measurement intervals can be set. 2. High-resolution thermal imaging system, the imaging picture is clear, and the imaging color can be freely marked according to the set temperature. 3. With hot zone alarm function, the alarm zone and temperature range can be set arbitrarily. 4. With hot zone tracking function 5. Equipped with special 7~14um infrared filter lens The technical parameters 1. Temperature measurement range: 200°C ~ 2000°C 2. Temperature measurement accuracy: 2% 3. Detection accuracy and alarm accuracy: ≥98% 4. Resolution: ≥ 0.5℃ 5. Pixels: 640x240PT 6. Band: 7~14um 7. Field of view: 7.5°×5.5° 8. Frame rate: ≥ 25 frames/sec 9. Equipment service life: ≥5 years 10. The normal operation rate of the automatic control system: ≥99%

The Non-contact AC Voltage Testers are easy to use — just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there’s voltage present. Electricians, maintenance, service, safety, personnel, and homeowners can quickly test for energized circuits in the workplace or at home. Can continuous self-test, so you always know it’s working Upon detection, tip glows and beeper sounds Expanded range: 90V to 1000V AC Features: Non-Contact Detection of AC Voltage from 90VAC to 1000VAC(50/60Hz) Rugged, double molded case Suitable for outlets or against wire insulation testing Flashing red LED light indicator Built-in bright fl ashlight with ON/OFF button Convenient size with pocket clip For use on 50/60Hz circuits Blue light means you’re close Red LED light and audible beeper indicator NCV, wide range and high sensitivity from 12V to 1000V Battery: 2x“AAA”1.5V

Product Specification: This is a high-tech product supports Full HD 1920x1080P video recording at 15fps, and photo taking at 2272x1704 pixel, just needs you to insert a Micro SD card into the card slot, then you’re ready to go for video & audio recording, only audio recording, photo taking and motion detection. • Leather belt motion detection Belt Camera DVR • Remote control • 5 night light • 1920x1080P • 300 million pixels • support for work 3 hours Package Contents: 1X Leather belt Camera Night Vision motion detection DVR 1X Remote controller 1X USB cable 1X User manual Price:-10000 We Provide Home Delivery Anywhere in Pakistan More Info Call:-03458423444, 03331474833 Or Visit:-www.tellebrand.com Email:-order@tellebrand.com http://www.tellebrand.com/motion-detection-camera-belt-in-pakistan

Product Specification: This is a high-tech product supports Full HD 1920x1080P video recording at 15fps, and photo taking at 2272x1704 pixel, just needs you to insert a Micro SD card into the card slot, then you’re ready to go for video & audio recording, only audio recording, photo taking and motion detection. • Leather belt motion detection Belt Camera DVR • Remote control • 5 night light support for work 3 hours Package Contents: 1X Leather belt Camera Night Vision motion detection DVR 1X Remote controller 1X USB cable 1X User manual Price:-10000 We Provide Home Delivery Anywhere in Pakistan More Info Call:-03458423444, 03331474833 Or Visit:-www.tellebrand.com Email:-order@tellebrand.com http://www.tellebrand.com/motion-detection-camera-belt-in-pakistan

Overview The system realizes the fixed-length measurement of the width, thickness and length of the continuously cast product through machine vision and laser rangefinding system. The measured data is transmitted to the host system through the optical fiber. The host system calculates the weight of each billet according to different steel grades and specific gravity, so that we can realize the fixed length measurement and fixed weight control of the cast products and the precise control of the steelmaking process in the production process. After cutting the billets by fixed weight and length, the fixed weight cut-to-length system is checked by the online weighing measurement system, so as to give feedback to the fixed length model of control system. The slab number (automatic checking) can also be automatically identified online by using machine vision, and the weight and slab number can be automatically stored in the local database for use in the production and management system. The measuring principle of the system On the upper surface of the billet, a set of linear CCD cameras and a laser rangefinding instrument are respectively installed. Through machine vision and laser correction, we can achieve precise measurement of the cast products’ shape. Through accurate cast products’ shape monitoring, the billet thermal expansion coefficient of cast products and cast products’ density at the current temperature, we can obtain the quality of the billet. At the same time, we can achieve high-precision quality cut-to-length , namely, fixed-weight and fixed-length. The system can be matched with the weight detection and calibration system. The system adopts the online barrier-free hidden integral roller table weighing method for continuous casting products, and connects its weighing data into the intelligent control model. The model and steel billet weighing system, and the fixed weight cut-to-length system realize the closed-loop control of the system model, and optimize the fixed weight accuracy through automatic signal collection. The features of the equipment The cutting control technology for fixed-length and fixed-weight of cast products is a concrete manifestation of the lean production management of steel products. In the era of high-quality competition of steel products, only high-end intelligent technology and management can reduce costs, improve quality and market competitiveness. 1. Data management can be carried out according to shifts, pouring times, days, weeks, months, etc., as well as data management according to specifications, production capacity, quality, etc. 2. Each stream can send out signals such as pre-clamping, clamping, cutting, roll-up, roll-down and return of the cutting car according to the user's requirements. 3. The detection and cutting precision is high, the controllable length sizing accuracy is ±1mm, and the quality sizing accuracy is more than 1.5‰. 4. It is not sensitive to other high-intensity light interference, and overcomes the influence of light sources such as sunlight and arc welding. 5. The monitor displays the running status of the current hot billet in real time and displays the corresponding parameters. 6. Laser rangefinding and CCD machine vision are used to calculate the weight of the cast products and optimize the cutting to length. 7. Historical cutting data is automatically stored, and the system can set rules for historical data. 8. Support the free transformation of fixed length, and a variety of operation modes are available for the operator to choose. 9. Adopt advanced high temperature laser measurement and high pixel linear CCD technology. 10. The system provides abundant interfaces, which can communicate with the PLC control. 11. Applicable to all kinds of continuous casting machine flame cutting system. 12. Provide automatic, upper and manual cutting control. The main technical requirements 1. Width range of the inspected cast product: 120~2000 mm 2. Length range of the inspected cast product: 1000~20000 mm 3. Thickness range of the inspected cast product: 35~400 mm 4. Steel billet moving speed: 3.5 m/s 5. Billet running speed: 6.5m/min 6. Temperature of the measured steel billet: 0~850 °C 7. Measurement accuracy: width ±0.2mm thickness ±0.2mm length ±0.2mm 8. Fixed weight accuracy: 0.8‰ (temperature model verification) 9. Quality inspection check: 1‰

The composition of the system The photoelectric strip automatic center position control system is mainly composed of sensors, amplifiers, PLC controllers, hydraulic control and other parts. System composition block diagram The main technical parameters 1. Detection width: 300-2800mm 2. Detection light source: 220VAC. (100VAC) 30W. High frequency white light works continuously 3. Photodetector: precision die-casting components, time constant 20ms 4. Maximum working voltage: 50VDC 5. Distance from receiver to emitter: 300-1000mm 6. Operating temperature: 0℃-60℃ 7. Resolution: 0.5mm 8. Linearity: ±1%F.S (after linearization) 9. Repeatability error: △R1%, F.S 10. Servo-valve working signal: ±10V 11. Rated pressure (oil pressure): 4.5Mpa 12. Rated flow: 30L/min 13. Symmetry: 10%

Specification: • Material: ABS • Net Weight: 58g • Size (L x W x T): 93 x 48 x 17mm • RF signal detector antenna length: 180mm • Receiving Range: 1MHz - 6500 MHz • Probe Laser Wavelength: 920nm • Operating Current: 8mA • Built-in rechargeable: 280mAh • Radio Detection of camera range: 5cm -10m (according to power) • Laser Detection camera: from 10cm - 10m • Color: Black Highlights: • Detects wireless signals (used by spy devices) around you • Combined Laser scanning and radio frequency sweep • Detect and locate any wired, wireless hidden camera and RF device with working frequency between 1MHz - 6.5 GHz • Special LED + camera lens detector window allows you to sweep areas for regular security cameras and hidden pinhole cameras (camera lens produces a red reflective spot through the red detector window) • Great for spotting cell phone / GPS spy devices, signal blockers, and other wireless surveillance devices • Multi-function warning: Laser Light, vibration, Sound, LED display, Earphone • Adjustable sensitive step • Built-in Compass especially for professional users • Low power indication • Comes with 2.5mm jack earphones+100V~240V AC charger + English User Manual • Note: Correct plug type or adapter will be sent according to your shipping country. What's in the box? • 1 x Anti-Spy Detector • 1 x AC Adapter • 1 x 2.5mm Jack Earphones • 1 x English User Manual Price:-12000 We Provide Home Delivery Anywhere in Pakistan More Info Call:-03458423444, 03331474833 Or Visit:-www.tellebrand.com Email:-order@tellebrand.com http://www.tellebrand.com/spy-camera-wireless-detector-in-pakistan

Specification: • Material: ABS • Net Weight: 58g • Size (L x W x T): 93 x 48 x 17mm • RF signal detector antenna length: 180mm • Receiving Range: 1MHz - 6500 MHz • Probe Laser Wavelength: 920nm • Operating Current: 8mA • Built-in rechargeable: 280mAh • Radio Detection of camera range: 5cm -10m (according to power) • Laser Detection camera: from 10cm - 10m • Color: Black Highlights: • Detects wireless signals (used by spy devices) around you • Combined Laser scanning and radio frequency sweep • Detect and locate any wired, wireless hidden camera and RF device with working frequency between 1MHz - 6.5 GHz • Special LED + camera lens detector window allows you to sweep areas for regular security cameras and hidden pinhole cameras (camera lens produces a red reflective spot through the red detector window) • Great for spotting cell phone / GPS spy devices, signal blockers, and other wireless surveillance devices • Multi-function warning: Laser Light, vibration, Sound, LED display, Earphone • Adjustable sensitive step • Built-in Compass especially for professional users • Low power indication • Comes with 2.5mm jack earphones+100V~240V AC charger + English User Manual Price:-12000 We Provide Home Delivery Anywhere in Pakistan More Info Call:-03458423444, 03331474833 Or Visit:-www.tellebrand.com Email:-order@tellebrand.com http://www.tellebrand.com/spy-camera-wireless-detector-in-pakistan

Specification: Material: ABS Net Weight: Smm RF signal detector antenna length: 180mm Receiving Range: MHz Probe Laser Wavelength: nm Operating Current: 8mA Built-in rechargeable: mAh Radio Detection of camera range: 5cm -10m (according to power) Laser Detection camera: from 10cm - 10m Color: Black Highlights: Detects wireless signals (used by spy devices) around you Combined Laser scanning and radio frequency sweep Detect and locate any wired, wireless hidden camera and RF device with working frequency between 1MHz - 6.5 GHz Special LED + camera lens detector window allows you to sweep areas for regular security cameras and hidden pinhole cameras (camera lens produces a red reflective spot through the red detector window) Great for spotting cell phone / GPS spy devices, signal blockers, and other wireless surveillance devices Multi-function warning: Laser Light, vibration, Sound, LED display, Earphone Adjustable sensitive step Built-in Compass especially for professional users Low power indication Comes with 2.5mm jack earphones+100V~240V AC charger + English User Manual Note: Correct plug type or adapter will be sent according to your shipping country. What's in the box? 1 x Anti-Spy Detector 1 x AC Adapter 1 x 2.5mm Jack Earphones 1 x English User Manual Order Now :

Specification: Material: ABS Net Weight: 58g Size (L x W x T): 93 x 48 x 17mm RF signal detector antenna length: 180mm Receiving Range: 1MHz - 6500 MHz Probe Laser Wavelength: 920nm Operating Current: 8mA Built-in rechargeable: 280mAh Radio Detection of camera range: 5cm -10m (according to power) Laser Detection camera: from 10cm - 10m Color: Black Highlights: Detects wireless signals (used by spy devices) around you Combined Laser scanning and radio frequency sweep Detect and locate any wired, wireless hidden camera and RF device with working frequency between 1MHz - 6.5 GHz Special LED + camera lens detector window allows you to sweep areas for regular security cameras and hidden pinhole cameras (camera lens produces a red reflective spot through the red detector window) Great for spotting cell phone / GPS spy devices, signal blockers, and other wireless surveillance devices Multi-function warning: Laser Light, vibration, Sound, LED display, Earphone Adjustable sensitive step Built-in Compass especially for professional users Low power indication Comes with 2.5mm jack earphones+100V~240V AC charger + English User Manual Note: Correct plug type or adapter will be sent according to your shipping country. What's in the box? 1 x Anti-Spy Detector 1 x AC Adapter 1 x 2.5mm Jack Earphones 1 x English User Manual Order Now :

About us: Glisten Security is a first Pakistani electronics security brand for home & office security, Our solutions that use cloud technology include CCTV cameras, Time Attendance, Access Control, Home/Office Alarm, Baby Watch, People Counter & more. For further details: Contact: 042-35443103, 0322-Glisten(4547836) Email: info@glistensecurity.com PRODUCT: Wireless WiFi CCTV IP Network Camera Audio Pan/Tilt P2P IR Night Vision - GLISTEN Specifications: Features : 1. System Security Supports there-level account, password, user authority management 2. DDNS Free DDNS bounded 3. P2P No need to preset camera, Offer free factory P2P(JWEV-000xxx-xxxxx), Plug&play, Support QR code scanning to view 4. Cell Phone View Support Iphone and andriod smart view via QR code scanning. 5. TF Card Record Support 32G TF card . Support the record view via browser or read the record documents in the TF Card directly. 6. Lens Lens Type: Glass Lens Standard : 3.6 mm 7. Video Image Compression: MJPEG Image Frame Rate: 25fps(50Hz),30fps(60Hz) Resolution: 640 x 480(VGA), 320 x 240(QVGA) Flip Mirror Images, Vertical / Horizontal, Light Frequency, 50Hz, 60Hz or Outdoor, Video Parameters, Brightness, Contrast 8. Night Visibility 13 Φ5 IR LEDs, Night visibility up to 10 meters 9. Audio Input / Output: Built-in Microphone/Built-in Speaker Audio Compression: ADPCM Audio Gain: AGC Audio Interface: Audio IN / Audio Out 10. Pan/Tilt Rotation Angle: Pan:270°, Tilt: 90° Rotation Speed: 10 Level PT Speed Optional, Speed Range 5-50°/ Second, Preset - Support 16 Preset Positions 11. Network Ethernet, One 10/100Mbps RJ-45 Supported Protocol: HTTP,FTP,TCP/IP,UDP, SMTP,DHCP,PPPoE,DDNS,UPnP etc. IP Mode: Dynamic IP address, static IP address, PPPOE Online Visitor: Support 4 visitors at the same time 12. Wireless Wireless Standard IEEE 802.11b/g/n Wireless Security WEP, WPA, WPA2 Encryption 13. Others: Product Type Cartoon Robot/ Indoor use Power DC5V 2A Working Temperature: -10~50 °C Working Humidity: 95% RH Size: Item Size: 112mm x 98mm (HxW) Packaging Size: 182mm x 110mm x 149mm (LxWxH) 14. Weight: N.W.: 290g G.W.: 600g(Note:Actual Weight Final) 15. Accessories: Adaptor, CD (including manual), Bracket, Screw 16. Alarm: Alarm Detection: Motion detection ,Motion Detect Sensibility can be adjusted Alarm Action: Support Email photo, FTP photo etc. 17. System: Supported OS: Microsoft Win98 SE/ME/2000/XP/Vista/Windows7 32Bit / Mac OS. Browser: IE6.0, IE7.0, IE8.0, FireFox, Google or other standard browser Certification: CE,FCC,RoHS 18. Whats in the BOX: Wanscam wireless security camera Wireless Antenna Power Supply Unit Wall Mounting Stand (Adjustable and Removeable) Installation CD & Manual

Spy Camera Detector in pakistan country Specification: Material: ABS Net Weight: 58g Size (L x W x T): 93 x 48 x 17mm RF signal detector antenna length: 180mm Receiving Range: 1MHz - 6500 MHz Probe Laser Wavelength: 920nm Operating Current: 8mA Built-in rechargeable: 280mAh Radio Detection of camera range: 5cm -10m (according to power) Laser Detection camera: from 10cm - 10m Color: Black Highlights: Detects wireless signals (used by spy devices) around you Combined Laser scanning and radio frequency sweep Detect and locate any wired, wireless hidden camera and RF device with working frequency between 1MHz - 6.5 GHz Special LED + camera lens detector window allows you to sweep areas for regular security cameras and hidden pinhole cameras (camera lens produces a red reflective spot through the red detector window) Great for spotting cell phone / GPS spy devices, signal blockers, and other wireless surveillance devices Multi-function warning: Laser Light, vibration, Sound, LED display, Earphone Adjustable sensitive step Built-in Compass especially for professional users Low power indication Comes with 2.5mm jack earphones+100V~240V AC charger + English User Manual Note: Correct plug type or adapter will be sent according to your shipping country. What's in the box? 1 x Anti-Spy Detector 1 x AC Adapter 1 x 2.5mm Jack Earphones 1 x English User Manual Order Now: We are just a call away 0321-4212615