Charging voltage5v battery

Portable Mini Fan Usb Charging rechargable battery 3 speed Chargeable Fan with Mini light. Can be used while charging or unplugged if charged Charges with 5 volt mobile charger. small cable and 18650 battery included. Indication for charging and fan speed. Good for Work desk, Car, etc

Product Features:* Mini size & lightweight* Portable & handy* Rechargeable Battery Powered* USB Powered and Charging* Long battery life* Build in LED light(great for outdoors, camping)* Wide applications

Features: LED lighting function. 3 mode speed regulation. Adopted 4.5W brushless motor industrial grade fan (4 inch), strong winds and long life. The battery bin is a detachable structure, which is convenient for users to use or replace the battery. USB interface charging or 18650 battery power supply.

Product Highlights 1. Compact appearance and easy to carry2. Fast charging, low consumption3. Three-speed wind speed, adjust with you4. LED Light Feature: USB Rechargeable Product introduction: Input: 100-240V ACOutput: 5V 1A DCPower: 5.4WCharging time: 5 hoursUse time: 3-8 hoursGear position: third gearSize: 15x11.5x5CMMaterial: ABS, PP Product Highlights 1. Compact appearance and easy to carry2. Fast charging, low consumption3. Three-speed wind speed, adjust with you4. LED Light Feature: USB Rechargeable Product introduction: Input: 100-240V ACOutput: 5V 1A DCPower: 5.4WCharging time: 5 hoursUse time: 3-8 hoursGear position: third gearSize: 15x11.5x5CMMaterial: ABS, PP

Compact appearance and easy to carry Fast charging, low consumption Three-speed wind speed, adjust with you LED Light Feature: USB Rechargeable Product introduction: Input: 100-240V ACOutput: 5V 1A DCPower: 5.4WCharging time: 5 hoursUse time: 3-8 hoursGear position: third gearSize: 15x11.5x5CMMaterial: ABS, PP

Product Highlights 1. Compact appearance and easy to carry2. Fast charging, low consumption3. Three-speed wind speed, adjust with you4. LED Light Feature: USB Rechargeable Product introduction: Input: 100-240V ACOutput: 5V 1A DCPower: 5.4WCharging time: 5 hoursUse time: 3-8 hoursGear position: third gearSize: 15x11.5x5CMMaterial: ABS, PP

Using the module:Connect micro USB cable for power, or 5V DC to pads marked IN+ and IN- on the left-hand side of the module Connect cell to charge to B+/B- pads on the right-hand side of the module. A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side Important! Disconnect load when charging The red LED indicates charging in progress, the green LED indicates charging has finished. Never charge your battery at a rate greater than 1C. 2. It is better thanthe charging current is 37% of the battery capacity. If you charge the battery of 1000mAh, acurrent of 400mAh is enough. 3. The connection wire should not be too thick. 4. Make sure the connect point is good. 5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is a protection function, auto-subtract the charging current to avoid burn damage to thechip. 6. NO Reverse polarity.Features:Led indicator: red is charging Green is fully charged. Current Protection: Yes Inversed polarity: NO. Use mature charging chip TP4056 for simple peripheral circuits, good protection performance, and high charging accuracy. Fully machinery automated processing, all patch parts manufacturing.

DESCRIPTION Features: This is the mobile power module Accessories, 18650 Circuit board shell. Meet the individual needs of your DIY, but you must understand basic electronic assembly. Motherboard comes with protection function: Charging overcharge protection, over-discharge protection, overcurrent protection. Intelligent output device after charging full, automatically stop charging, to prevent mobile phones overcharge. Output voltage and current stable, will not harm user devices. Specifications: Micro USB input: 5V 1A USB Output: 5V 2.1A / 5V 1A(Dual USB interface) Charging display: intelligent digital display Batteries Type: liquid lithium-ion batteries (18650) Product Size: 57mm x 28mm Screen size:27mm x 17mm Installation instructions: The circuit board is connected to the battery negative B-, B + is the positive, do not connecting reversed, connecting reversed will burn the board, the battery is connected in parallel welding, assembling battery. Note that the insulation between the battery and the circuit board, battery lead not to touch the circuit board, so as not to cause a short circuit. Package included: 1 x Mobile Power Bank 18650 Battery Charger PCB Mention that you found this ad on DealMarkaz.pk when you call.

Description: Details iShopping.pk brings you the best price for Shure Networked 2-Port Charging Station (MXWNCS2) with express shipping all over Pakistan.   The MXWNCS2 Networked 2-Port Charging Station from Shure is capable of charging MXW1 and MXW6 microphone transmitters (not compatible with MXW8 gooseneck microphones). It also links the microphones to access point channels and networks battery statistics to the control software.   Features: Charge Status Indicators 5-segment LEDs on the unit display charge status individually for every docked microphone transmitter Remote Charge Status Monitoring Ethernet connection to the system enables remote monitoring of battery charge status in hours and minutes via Microflex Wireless Control Software or third-party control systems Easy Transmitter Linking Assign docked wireless microphones to channels on an access point transceiver by simply pressing "Link Rapid Charge Times Reaches 50% charge in one hour and fully charges transmitters in two hours Overcharge Protection Smart recharging circuitry safeguards against battery damage and extends life cycles

Manage the constant current to constant voltage charging of a connected lithium battery Over-discharge protection - keeps your battery from being discharged below 2.4V, a healthy minimum voltage level for your batteryIf a connected battery has been discharged below 2.4V the module will cut output power from the battery until the battery voltage has been re-charged above 3.0V (the over-discharge release voltage), which at that time the module will again allow discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows charging of the battery to occur through the parasitic diode of the discharge control MOSFET (FS8205A Dual MOSFET). Overcharge protection - the module will safely charge your battery to 4.2V Overcurrent and short-circuit protection - the module will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs Soft-start protection limits inrush current Trickle charge (battery reconditioning) - if the voltage level of the connected battery is less than 2.9V, the module will use a trickle charge current of 130mA until the battery voltage reaches 2.9V, at which point the charge current will be linearly increased to the configured charge current.

Description: Details iShopping.pk brings you the best price for Shure 4-Port Networked Charging Station (MXWNCS4) with express shipping all over Pakistan.   The  MXWNCS4 4-Port Networked Charging Station  from Shure is designed to provide networked charging for up to 4 Microflex wireless transmitter units. Thanks to its networking abilities, the MXWNCS4 can display charge time info to networked computers in addition to being able to assign channels to docked transmitters.   Features: • Station accepts all Microflex Wireless transmitters • Charge status indicators: 5-segment LEDs on the unit display charge status individually for every docked microphone • Remote charge status monitoring: Ethernet connection to the system enables remote monitoring of battery charge status in hours and minutes via the control software or third party control systems • Transmitter linking: Assign docked wireless microphones to channels on an Access Point Transceiver by simply pressing "link" • Rapid charge times: Reaches 50% charge in one hour and fully charges transmitters in two hours • Overcharge protection: Smart recharging circuitry safeguards against battery damage and extends life cycles   Specifications: Charge Time MXW1, MXW6, MXW8: 50% = 1 hour, 100% = 2 hours  MXW2: 50% = 1.5 hours, 100% = 3 hours Network Interface 10/100 Mbps Ethernet Power Requirement 15 V DC @ 3.3 A maximum, supplied by external power supply (tip positive) Housing Molded plastic, cast zinc Dimensions (HxWxD) 2.7 x 7.5 x 7.25" (68 x 191 x 184 mm) Weight 3.7 lb (1.7 kg)

100% New and High Quality Micro USB TP4056 Dual Charging Module Input Voltage: 4.35V - 6V (recommended voltage 5v) Chargingcut-off Voltage: 4.2V (± 1%) Maximum Charging Current Output: 1000mA (1A) Battery Discharge Protection Voltage: 3.0V Charging Status LEDs:Red LED Charging, Green LED Fully Charged Note: The installation and usgae of these modules require some basic knowledge of electronics, if you dont know how to install, please don't buy it.

APNI BATTERY KO DEIN NEW LIFE AND BACKUP For Lead Batteries Power Enhancement BPP working is very simple. Once you add BPP to your battery and put the battery on charging, the heat passing through the battery plates help dissolve BPP from a layer and breaking down the sulphation. How to Use? You must shake well before using.Please avoid contact with metals and direct sunlight.Please do wear safety glasses while working around batteries.Add BPP to battery according to Dosage Chart below.Please give 48 hours of charging to the battery after using BPP, while you may also continue to normal use while BPP keeps working in the background to improve your battery performance. Please always wash hands with soap after use. https://www.facebook.com/batterypowerpluss FOR DELIVERY:

Module name: 3S 12.6V Li-ion Lithium Battery 18650 Charger Protection Board Suitable range: For nominal voltage 3.6V 3.7V lithium battery(Including 18650,26650, lithium polymer batteries) Charging voltage: 12.6V Maximum output current: 20A Maximum output power / charging power: 252W Color: green material: plastic Product size:59*20*3.4mm Product weight: 4.4g Package Contents: 1 PCS x 3 string 12.6V 20A 18650 lithium battery protection board Precautions: 1.Strictly according to the diagram wiring: 0V/4.2V/8.4V/12.6V,Otherwise it will cause damage to the chip. 2.After connection,it need to first charge activation, then will have the output.

Product Name: 3 string 12.6V 40A lithium battery protection board Charging voltage: DC 12.6V~13.6V Continuous discharge current: 40A maximum (if the heat dissipation environment is not good, please reduce the load current) Continuous charging current: up to 20A Balance Version Product size: 41*61*4mm Enhance Version Product size: 41*55*4mm Applicable choice: applicable to the nominal voltage of 3.7V, fully charged 4.2V lithium battery (including 18650, 26650, polymer lithium battery), can be drilled below 170W