Air fuel

Electronic fuel injection EFI Electrician course in Wahcantt, Kotli International college of technical education All type of courses and diplomas offered by international college of technical education is acceptable in international countries as well as in domestic country. Admission open the classes will be starting Soon, 03115193625. Electronic fuel injection replaces the need for a carburetor that mixes and fuel. EFI does exactly what it sounds like – it injects fuel directly into an engine's manifold or cylinder using electronic controls. A fuel injection system that uses external mixture formation is called a manifold injection system; there exist two types of manifold injection systems: multi-point injection (port injection), and single-point injection (throttle-body injection). The twists and turns of the intake runners can also cause the air and fuel mixture to separate as if flows to the cylinders, resulting in uneven fuel mixtures between cylinders. Electronic fuel injection (EFI) system use engine sensors, a computer and solenoid operated fuel injector to meter and inject right amount. The best fuel to air ratio for each cylinder is approximated for the best performance. Carburetors do last longer than fuel injection systems, and are cheap compared to fuel injectors. Fuel injection atomizes the fuel through a small nozzle under high pressure. A fuel injection conversion replaces a carburetor with a fuel injection system. There are fuel injection conversion kits that make the entire process very easy. Older cars have carburetors, but electronic fuel injection (EFI) offers greater fuel efficiency and improved performance. Engines equipped with EFI systems are inherently more reliable than carbureted engines. This follows from the ability of the EFI control systems to maintain optimum air/fuel ratios during all phases of flight. EFI systems are far less susceptible to icing, compared to carburetors. This fuel pump is located inside the fuel tank of the bike. ... The nozzle of the fuel injection system goes right into the chamber of the cylinder. Hence, the ECU directs the injectors to control the amount of fuel to enable the most efficient mode of combustion. Unified Extensible Firmware Interface (UEFI) is firmware code from a chip on your motherboard that provides extra functionality, beyond the Basic Input/Output System (BIOS). UEFI is a way to do things with your computer before an operating system is loaded. UEFI is the new replacement for BIOS, the efi is a name/label of the partition where UEFI boot files are stored. Somewhat comparable to the MBR is with BIOS, but much more flexible and allows multiple boot loaders to co-exist. The EFI System Cleaner service cleans your fuel injectors and combustion chambers and restores performance. The MPFI or multi point fuel injection system is a system or method of injecting fuel into internal combustion engine through multi ports situated on intake valve of each cylinder. It delivers an exact quantity of fuel in each cylinder at the right time. Single point fuel injection are systems that have a single injector, or a group of injectors clustered together in one, usually centralized spot on the intake manifold. ... Multi-point, or multi-port is when there is a fuel injector for each cylinder and they are located as close as possible to the intake valve. The fuel injection system can be divided into low-pressure and high-pressure sides. The low-pressure components include the fuel tank, fuel supply pump and fuel filter. The high-pressure side components include a high pressure pump, accumulator, fuel injector and fuel injector nozzle. When you maintain your vehicle, it is important to have parts and components checked regularly. The function of the fuel system is to store and supply fuel to the engine and cylinder chambers. There, it can be mixed with air, vaporized, and then burned to produce the energy. An Injection Pump is the device that pumps fuel into the cylinders of a diesel engine. Traditionally, the injection pump was driven indirectly from the crankshaft by gears, chains or a toothed belt (often the timing belt) that also drives the camshaft. The main types of injection systems include pump-line-nozzle, unit injector, and common rail. Modern injection systems reach very high injection pressures, and utilize sophisticated electronic control methods. At first, carburetors were replaced with throttle body fuel injection systems (also known as single point or central fuel injection systems) that incorporated electrically controlled fuel-injector valves into the throttle body. Carburetors have largely been supplanted in the automotive and, to a lesser extent, aviation industries by fuel injection. They are still common on small engines for lawn mowers, rototillers, and other equipment. While carburetors may not have a life in new vehicles today, chances are good that they'll still be used for many years to come. Curious to get your own vehicle's carburetor checked out? Check out our full range of services to get your car in top form!. Modern motorcycles have computer controlled fuel injectors. You can also convert an older motorcycle into a fuel injection system with motorcycle fuel injection conversion kits. If you prefer, you can convert from carbureted to fuel injection (otherwise known as carb to efi). Electronic fuel injection EFI Electrician course in Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. for further detail of all courses our the website www.icollegete.com www.courses.com.pk

Electronic fuel injection Efi Course in Rawalpindi punjab 03115193625 Electronic Fuel Injection Course in Rawalpindi punjab 03354176949 International college of technical education offers Electronic fuel injection Efi Course in rawalpindi Pakistan Admission open for admission and queries call 03115193625. 03354176949 Electronic Fuel Injection Efi Course in Rawalpindi Punjab pakistan 03115193625, EFi Electronic Fuel Injection Course in Rawalpindi Punjab Pakistan The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. International college of technical education EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. International college of technical education offer Electronic Fuel injection Course in Rawalpindi punjab

Electronic fuel injection Efi Course in Rawalpindi shamsabad punjab 03115193625 Electronic Fuel Injection Course in Rawalpindi shamsabad punjab 03354176949 International college of technical education offers Electronic fuel injection Efi Course in rawalpindi Pakistan Admission open for admission and queries call 03115193625. 03354176949 Electronic Fuel Injection Efi Course in Rawalpindi Punjab pakistan 03115193625, EFi Electronic Fuel Injection Course in Rawalpindi Punjab Pakistan The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. International college of technical education EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. International college of technical education offer Electronic Fuel injection Course in Rawalpindi punjab

Electronic fuel injection Efi Course in Rawalpindi Murree road 03115193625, EFI Fuel injection Efi Course In Rawalpindi Murree road 03354176949 International college of technical education Offers EFI Auto Electrician Course For admission and queries call 03115193625, 03354176949 EFi Electronic Fuel Injection Course in Rawalpindi Punjab Pakistan The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. International college of technical education EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. International college of technical education offer Electronic Fuel injection Course in Rawalpindi murree road pakistan admission open for admission and information call 03115193625, 03354176949 for more information visit pour website www.icollegete.com.

Electronic fuel injection Efi Course in rawalpindi murree road punjab 03354176949 Electronic fuel injection Efi course In Rawalpindi Murree road punjab 03115193625 International college of technical education offers Electronic fuel injection Efi Course in rawalpindi Pakistan Admission open for admission and queries call 03115193625. 03354176949 EFi Electronic Fuel Injection Course in Rawalpindi Punjab Pakistan The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. ICTE EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. Admission open International college of technical education offer Electronic Fuel injection Course in Rawalpindi punjab pakistan for admission call 03115193625.

Electronic fuel injection Efi Course in rawalpindi Murree road 03115193625, Efi Auto electrician EFI Course in rawalpindi murree road pakistan international college of technical education offer Electronic fuel injection course in rawalpindi admission open for admission and information call 03115193625 new session start. Efi The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. The fuel system is composed of the fuel tank, a high pressure pump, and some method for regulating fuel pressure. The injectors can be though of as electrically operated valves. The amount of fuel delivered to the engine is determined by size of the injectors, the amount of time that the injectors are open, and on the fuel pressure. The electronic controller to determines how much fuel is needed and commands the injectors to remain open for the necessary amount of time to deliver the needed fuel volume. The amount of time that the injector is open is called the pulse width and is usually expressed in milliseconds (one thousands of a second). A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables. EFI Course Content: Tools Power output Fuel efficiency Emissions performance Running on alternative fuels Reliability Driveability and smooth operation Initial cost Maintenance cost Diagnostic capability Range of environmental operation Engine tuning. international college of technical education offer Efi Electronic Fuel injection Efi Course in rawalpindi murree road admission open for admission and information visit our website www.icollegete.com , www.courses.com

Electronic Fuel Injection (EFI) Course in Jhelum sahiwal . Best institute for EFI Auto electrician course in Rawalpindi Islamabad Pakistan. The Electronic Fuel Injection system fitted to most modern vehicles combines sophisticated computer controls with a high pressure fuel delivery system to provide optimum power and fuel efficiency. The system is controlled by an electronic control unit (ECU). Automotive electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earth moving equipment, mining equipment, marine applications and agricultural equipment. Admission are open 923115193625. The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured.Electronic Fuel Injection (EFI) Course in Jhelum sahiwal .Auto Electricians specialize in installing and maintaining electrical systems contained in automotive vehicles. Auto Electricians mainly work for auto service centers where they install, inspect, repair, and maintain all the electrical parts contained in a vehicle. Auto Electrician Responsibilities: Installing new vehicle wiring systems. Installing and troubleshooting immobilizer and alarm systems. Gathering information from customers about issues with their electrical system. Diagnosing electrical issues and proposing a course of action. Providing customers with estimated time and cost for repairs. Repairing and replacing faulty wiring or electrical systems. Servicing of electrical automotive parts. Servicing and repairing electrical systems on agricultural vehicles. Maintaining a clean working environment. Completing job reports and processing paperwork. Electronic Fuel Injection (EFI) Course in Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. For further details of this course visit our website www.icollegete.com,www.courses.com.pk . International college of technical education offers different type of courses and diplomas out of which some are as follows: Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management

Electronic Fuel Injection (EFI) course in Rawalpindi Islamabad haripur hazara Jhelum chakwal +923115193625,Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625,World Wide Acceptable with UK/USA/Pak/ U.A.E/ KSA/China/ International Certifications in Rawalpindi, Islamabad, Efi Car Auto Electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Admission open for admission and queries call 03115193625, 03354176949 registered recognized, approved and authorized institute INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, registered recognized, approved and authorized institute For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to controll engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of “electronic control unit”, and then specific ECU’s were developed. Now, ECU’s are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU’s and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle. Auto Electrician Course Content: Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits.Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan.Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.Dubai , Abu Dabi , Muscat , Oman , Doha , Qatar ,South Africa , Saudia Arabia , kawat , Behrain , Kotli Sattian , Murree , UK , UAE , Sharja,Civil Technology Courses Diploma in Civil Surveyor Diploma in Quantity Surveyor Diploma in Civil Draftman Diploma in Civil Lab Technician Diploma in Civil Architecture Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management Diploma in Guest House Management DIT (Diploma in information technology) Revit 3D Cad Course Microstation Cad Course Shorthand Professional Course in Islamabad Shorthand Professional Course in Rawalpindi Shorthand Professional Course in Pakistan IATA Air Ticketing & Reservation Course in Islamabad IATA Air Ticketing & Reservation Course in Rawalpindi IATA Air Ticketing & Reservation Course in Pakistan Professional Cooking Course in Islamabad Professional Cooking Course in Rawalpindi Professional Cooking Course in Pakistan EFI Auto Electrician Course in Rawalpindi EFI Auto Electrician Course in Islamabad EFI Auto Electrician Course in Pakistan Civil 3D Course in Islamabad Civil 3D Course in Rawalpindi Civil 3D Course in Pakistan GIS Geographic Information Systems Course in Islamabad GIS Geographic Information Systems Course in Rawalpindi GIS Geographic Information Systems Course in Pakistan Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan.Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Admission open for admission and queries call 03115193625,03354176949 registered recognized, approved and authorized institute INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, registered recognized, approved and authorized institute For More Information Visit Our Website www.courses.com.pk, www.icollegete.com.

EFI Electronic Fuel Injection course in Rawalpindi Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, World Wide Acceptable with UK/USA/Pak/ U.A.E/ KSA/China/ International Certifications in Rawalpindi, Islamabad, Efi Car Auto Electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Admission open for admission and queries call 03115193625, 03354176949 registered recognized, approved and authorized institute INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, registered recognized, approved and authorized institute For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment, An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to controll engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of "electronic control unit", and then specific ECU's were developed. Now, ECU's are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU's and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle. ICTE Auto Electrician Course Content: Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits. Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan.Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.Dubai , Abu Dabi , Muscat , Oman , Doha , Qatar ,South Africa , Saudia Arabia , kawat , Behrain , Kotli Sattian , Murree , UK , UAE , Sharja,Civil Technology Courses Diploma in Civil Surveyor Diploma in Quantity Surveyor Diploma in Civil Draftman Diploma in Civil Lab Technician Diploma in Civil Architecture Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management Diploma in Guest House Management Diploma in International Tourism Management Diploma in Energy Management Diploma in Library Management Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management Diploma in Interior Designing Diploma in BMS (Building Management System) Hospitality Management Course in rawalpindi Hospitality Management Course in lahore Hospitality Management Course in peshawar Building Management System (BMS) Course in rawalpindi Building Management System (BMS) Course in lahore Building Management System (BMS) Course in peshawar Quality Assurance Quality Control Course in rawalpindi Quality Assurance Quality Control Course in lahore Quality Assurance Quality Control Course in peshawar Hotel Management Course in rawalpindi Hotel Management Course in lahore Hotel Management Course in peshawar Iosh MS Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. OSHA 30 USA Safety Course IADC Rig Pass Icertosh (International Certificate in Occupational Safety and Health) Safety Officer IRCA, ISO Certifications Nebosh IGC Course in Rawalpindi Nebosh IGC Course in islamabad Nebosh IGC Course in peshawar Nebosh IGC Course in karachi Nebosh IGC Course in lahore Nebosh IGC Course in pakistan Computer languages Software Engineering AutoCAD (Civil, Mechanical, Electrical) 3D Studio Max (Advanced) Computer Networking Web Development Information Technology (PG-DIT) Project Managment Professional (PMP) Prima Vera (Project Management) DIT (Diploma in information technology) Revit 3D Cad Course Microstation Cad Course Shorthand Professional Course in Islamabad Shorthand Professional Course in Rawalpindi Shorthand Professional Course in Pakistan IATA Air Ticketing & Reservation Course in Islamabad IATA Air Ticketing & Reservation Course in Rawalpindi IATA Air Ticketing & Reservation Course in Pakistan Professional Cooking Course in Islamabad Professional Cooking Course in Rawalpindi Professional Cooking Course in Pakistan EFI Auto Electrician Course in Rawalpindi EFI Auto Electrician Course in Islamabad EFI Auto Electrician Course in Pakistan Civil 3D Course in Islamabad Civil 3D Course in Rawalpindi Civil 3D Course in Pakistan GIS Geographic Information Systems Course in Islamabad GIS Geographic Information Systems Course in Rawalpindi GIS Geographic Information Systems Course in Pakistan Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Admission open for admission and queries call 03115193625, 03354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com.

Electronic Fuel Injection EFI Course In Rawalpindi Murree road 03115193625, Electronic Fuel Injection EFI Course in Rawalpindi murree road 03354176949 International College of Technical Education Offers EFI Electronic Fuel Injection Course in Rawalpindi Murree road For admission and queries call 03115193625, 03354176949, INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. An auto electrician is a tradesman specializing in electrical wiring of motor vehicles. Auto electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical components. Auto electricians specialize in cars and commercial vehicles. Auto electricians work in dealer workshops or in independent service centers, diagnosing and repairing a vehicle's electrical faults. As automotive systems increase in complexity and feature more electronic components and accessories, the role of auto electrician becomes more important. Experienced auto electricians might work as independent technicians, offering a specialist service to vehicle owners or service centers, Auto electricians work on all vehicle electrical systems and components, including ignition, fuel injection and engine management systems, anti-lock braking, battery, wiring and charging systems, heating and air conditioning systems, lighting and indicators. They must also be familiar with increasingly-sophisticated in-car entertainment systems, including radios and video players, cell phone, navigation and vehicle information systems. A key role for auto electricians is fault diagnosis. They meet vehicle owners to discuss problems and carry out tests to identify the problem. If a vehicle has starting problems, intermittent running faults or poor fuel consumption, they use specialist skills and tools to diagnose problems in the ignition, fuel injection and engine management systems. To diagnose a vehicle with braking problems that are not due to mechanical faults, auto electricians diagnose the anti-lock braking system. They also test the battery and charging systems to ensure that electrical components are receiving the correct voltage. Auto electricians test vehicle lighting systems to ensure they are operating correctly. They test headlight beam alignment and lighting intensity in line with specifications and make any necessary adjustments. They fit additional lighting components, such as fog lights or emergency lights, ensuring that they are correctly connected to the electrical system. This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician probably from a role where they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. International College Of Technical Education Offers Electronic Fuel Injection Diploma In rawalpindi murree road admission open for admission and information call us 03115193625, 03354176949

Electronic Fuel Injection Efi Course in rawalpindi murree road islamabad 03115193625, Electronic Fuel Injection EFI Course in rawalpindi Murree road Punjab pakistan 03354176949 International college of technical Education offer Electronic Fuel Injection EFI Course in Rawalpindi Murree road World Wide Acceptable with UK/USA/Pak/U.A.E/ KSA/China/ International Certifications in Rawalpindi,Islamabad, EFI Auto electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, Admission open We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations. Admission open in Complete efi course for admission and queries call 03115193625, 03354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Auto Electrician is there to service, maintain, check up, repair, and change electric and electronic devices and systems on the vehicle. A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions. An auto electrician is a tradesman specializing in electrical wiring of motor vehicles. Auto electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical components. Auto electricians specialize in cars and commercial vehicles. Auto electricians work in dealer workshops or in independent service centers, diagnosing and repairing a vehicle’s electrical faults. Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment As automotive systems increase in complexity and feature more electronic components and accessories, the role of auto electrician becomes more important. Experienced auto electricians might work as independent technicians, offering a specialist service to vehicle owners or service centers. Auto electricians work on all vehicle electrical systems and components, including ignition, fuel injection and engine management systems, anti-lock braking, battery, wiring and charging systems, heating and air conditioning systems, lighting and indicators. They must also be familiar with increasingly-sophisticated in-car entertainment systems, Auto electricians install new electrical or electronic components or accessories for customers. They may replace an entertainment system, for example, with a newer version or install a GPS navigation system. If an owner plans to tow a trailer or motor home, the auto electrician might modify the vehicle’s electrical system. including radios and video players, cell phone, navigation and vehicle information systems. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. International college of Technical Education Offer Electronic Fuel Injection EFI Course in Rawalpindi Murree road Shamsabad Murree road Islamabad Pakistan for more visit our website www.icollegete.com , www.courses.com.pk and call 03115193625, 03354176949

Electronic Fuel Injection Efi Auto Course in Attock Chakwal Dubai,Electronic Fuel Injection Efi Auto Course in Rawalpindi Islamabad Gujar Khan,international college of technical education in rawalpindi islamabad pakistan,best electronic fuel injection efi auto electrician diploma course in rawalpindi islamabad pakistan,best efi auto electrician diploma course in rawalpindi islamabad gujar khan pakistan 03115193625/03354176949,lowest fee electronic fuel injection efi auto electrician course in rawalpindi islamabad gujar khan pakistan,advance efi auto electrician fuel injection course in rawalpindi islamabad pakistan,Auto Electrician is there to service, maintain, check up, repair, and change electric and electronic devices and systems on the vehicle. A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions.Also, this tradesman should perform quality control for the electrical work performed, considering the norms and regulations.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.This training for auto electrician is the best and the most comprehensive possible offer.It is a reliable and high-quality course to prepare you for this trade, highly in demand.The practice within this training is certainly the most important segment.03115193625/03354176949 International College of Technical Education has a six-month auto electrician course to offer. Having finished this course, each student will be able to identify the types and elements of electric installations, and network equipment; to differ the electric symbols, and explain how the electric installations are set up on a vehicle.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.The auto electrician course in International College of Technical Education offers you the chance to learn about terms such as ECU, and CPU, learn what system sensors are, and explain how they work (coolant fluid temperature sensor, air temperature and flow sensor).In our school you will learn what an encoder is, how it functions, what is Hall effect, what is a “Knock” sensor, and what is the purpose of the sensor for the car speed.Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali. EFI Auto Electrician Course Contents: Tools Special purpose tools Measuring Instruments Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Batteries

Electronic Fuel Injection EFI course In Sargodha Sahiwal . Admission are open in international college of technical education 923115193625.Auto Electrician is there to service, maintain, check up, repair, and change electric and electronic devices and systems on the vehicle. A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions.Also, this tradesman should perform quality control for the electrical work performed, considering the norms and regulations.Within the auto electric trade courses, International College of Technical Education has a six-month auto electrician course to offer. Having finished this course, each student will be able to identify the types and elements of electric installations, and network equipment; to differ the electric symbols, and explain how the electric installations are set up on a vehicle.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.The auto electrician course in International College of Technical Education offers you the chance to learn about terms such as ECU, and CPU, learn what system sensors are, and explain how they work (coolant fluid temperature sensor, air temperature and flow sensor).In our school you will learn what an encoder is, how it functions, what is Hall effect, what is a “Knock” sensor, and what is the purpose of the sensor for the car speed.This training for auto electrician is the best and the most comprehensive possible offer.It is a reliable and high-quality course to prepare you for this trade, highly in demand.The practice within this training is certainly the most important segment. You can have the practice in a shop that ICTE Institute cooperates with, and it is not included in the course fee. Within the course fee we have included the textbook, the final exams, and a certified diploma. Electronic Fuel Injection EFI course In Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Visit our website for further details of this course www.icollegete.com,www.courses.com.pk. International college of technical education offers different type of courses and diplomas out of which some are as follows: Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management Diploma in Guest House Management Diploma in International Tourism Management Diploma in Energy Management Diploma in Library Management Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management

New session of EFI Auto Electrician course will be started soon in international college of technical education. Admissiona are open 03115193625. ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Auto electricians or automotive electricians concentrate on the electrical parts in motor vehicles.Their job descriptions entail installing, repairing, wiring, and maintaining of all electrical components found in different vehicles.They also check what is necessary to bring automobiles up to their best working condition.They may also treat equipment used in agriculture and mining such as excavators and tractors.Those in this line of work have to be technically knowledgeable in the use of equipment and machinery to do the job.They have to be familiar with how wires work and how they have to be placed in a vehicle.They also need to know the type of wiring techniques to utilize for the various components they work with.They must be good at testing equipment and the computers they use in mapping out electrical pathways and locating electronic problems or malfunctions in the system. They have to be able to dissemble, as well as correctly reassemble vehicle parts back together. They must be able to understand the equipment installed in each unit. They need to make sure the equipment is fully functional and clean, as well as making sure it is connected to the automobile’s main power source. Auto electricians also use meters and circuit diagrams to search for faulty parts of vehicles. EFIAuto Electrician Diploma Course in Rawalpindi Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, he design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7″ Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualifie staff.call03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com.Pakistan.Basic IT Course (MS Office) Computer Hardware Course Computerized Accounting CIT (Certificate in information Technology) Web & Graphic Designing Computer languages Software Engineering AutoCAD (Civil, Mechanical, Electrical) 3D Studio Max (Advanced) Computer Networking Web Development Information Technology (PG-DIT) Project Managment Professional (PMP) Prima Vera (Project Management) DIT (Diploma in information technology) Revit 3D Cad Course Micro station Cad Course Shorthand Professional Course in Islamabad Shorthand Professional Course in Rawalpindi Shorthand Professional Course in Pakistan.Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management Diploma in Fast Food Management Diploma in Flood Risk Management Diploma in Guest House Management Diploma in International Tourism Management Diploma in Energy Management Diploma in Library Management Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management Diploma in Interior Designing Diploma in BMS (Building Management System) Hospitality Management Course in rawalpindi Hospitality Management Course in lahore Hospitality Management Course in peshawar Building Management System (BMS) Course in rawalpindi Building Management System (BMS) Course in lahore Building Management System (BMS) Course in peshawar Quality Assurance Quality Control Course in rawalpindi Quality Assurance Quality Control Course in lahore Quality Assurance Quality Control Course in peshawar Hotel Management Course in rawalpindi Hotel Management Course in lahore Hotel Management Course in peshawar Iosh MS OSHA 30 USA Safety Course IADC Rig Pass Icertosh (International Certificate in Occupational Safety and Health)Safety Officer IRCA, ISO Certifications Nebosh IGC Course in Rawalpindi Nebosh IGC Course in islamabad Nebosh IGC Course in peshawar Nebosh IGC Course in karachi Nebosh IGC Course in lahore Nebosh IGC Course in pakistan Basic IT Course (MS Office) Computer Hardware Course Computerized Accounting CIT (Certificate in information Technology)

EFI Auto car Electrician course in Attock Jhelum . International college of technical education is best institute which offers national and international courses and diplomas which are acceptable in international countries as well as in domestic country.Admission are open in international college of technical education 923115193625. The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.call 03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com. International college of technical education offers different type of courses out of which some are as follows: Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Diploma in Mechanical Technology One Year Diploma in Mechanical Technology Two Years Diploma in Project Management (DPM) Diploma in Hotel Management Diploma in Hospitality Management Diploma in Quality Assurance (QA) Diploma in Quality Control (QC) Diploma in Total Quality Management (TQM) Diploma in Import & Export Management Diploma in College and University Management Diploma in Auditing Diploma in Accounts Management

EFI Auto Car Electrician Course In Sahiwal Sargodha.ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625. International college of technical education is best institute which offers The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan. EFI Auto Car Electrician Course In Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Visit our webistes for further details of this course www.icollegete.com,www.courses.com.pk

EFI Auto Electrician Course In Chakwal Sahiwal . ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625. The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi Pakistan. EFI Auto Electrician Course In Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Visit our website for further details of this course www.icollegete.com,www.courses.com.pk

EFI Auto Car Electrician Course In Bannu Kahuta . Best EFI Auto Electrician Course offered by international college of technical education. High Quality assistance provided by international college of technical education to students.ICTE offers different types of international Courses which are accepted in domestic country as well as in international coutries i.e China Japan Korea Saudia Dubai Muscat Oman Iran Tehran Qatar and all other international countries.Admission open for both boys and girls 03115193625.The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operation Engine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing. Visit our website for further details of this course www.icollegete.com,www.courses.com.pk. International college of technical education offers different type of courses and diplomas out of which some are as follows: Diploma in Education Planning and Management Diploma in Management Information System (MIS) Diploma in Software Project Management Diploma in Business Administration and Management Diploma in Office Administration & Management Diploma in Interior Designing Diploma in BMS (Building Management System) Hospitality Management Course in rawalpindi Hospitality Management Course in lahore Hospitality Management Course in peshawar Building Management System (BMS) Course in rawalpindi Building Management System (BMS) Course in lahore Building Management System (BMS) Course in peshawar Quality Assurance Quality Control Course in rawalpindi Quality Assurance Quality Control Course in lahore Quality Assurance Quality Control Course in peshawar Hotel Management Course in rawalpindi

EFI Auto Car Theory + Practical Training Course in Rawat Sahiwal . New session of EFI Auto Car electrician course will be started soon in international college of technical education. Admission are open in international college of technical education for both boys and girls 923115193625. Best institute for EFi Auto Electrician course in Rawalpindi pakistan.The design goal for an EFI system is to deliver the correct air fuel ratio for varying load, speed and temperature. Most modern EFI systems are incorporated in an ECU which also controls the ignition system, and may control may other functions such as anti-lock brakes, traction control systems, the transmission, etc. A fuel injection system itself consists of a source of pressurized fuel, fuel injectors and the electronic controller. A simple EFI system can operate fairly effective with just these three inputs. However, many systems include additional inputs from the following types of sensors. Most sensors are of one of two types. Some are simple on-off switches or counters, such as a gear indicator or tachometer. Most measure continuous variables like temperature or airflow. These sensors produce a 0-5v output. This signal is read by the ECU (computer). By referring to a calibration table, the ECU translates the signal into a value representing the physical parameter which is being measured, such as airflow in units of mass/time or temperature. The tuning process boils down in most cases to changing the values in these tables.Mass Air Flow (MAF – a sensor which directly measures airflow into the motor)Intake Air Temperature (IAT – an electronic temperature sensor to measure the temperature of the air entering the motor)Coolant Temperature Sensor (ACT – an electronic temperature sensor to measure the temperature of the engine coolant)Vehicle Speed Sensor (VSS – an electronic speedometer)Oxygen sensor (O2 sensor – measures the amount of oxygen in the exhaust which reflects the A:F (air:fuel) ratio)Knock sensor (a microphone which picks up the characteristic sound of engine knock)Crankshaft position (a magnetic sensor that tells the ECU which cylinder is ready to fire or receive fuel)Transmission sensors (these may include gear selection, pressure, and temperature sensors)Emission control device operation (a variety of functions may be monitored by different sensors)Advanced Throttle Body Fuel injectionNo tuning experience required – System provides self-mapping fuel technology to continually monitor and adjust fuel calibrationReady to run right out of the box with pre-loaded calibrations Supports fully programmable Ignition Control to optimize performance and fuel economyAccepts traditional round air cleaners and maintains same hood clearance as a carbEasy to use E Tuner App that communicates via Bluetooth wireless for ECU setup and engine tuning adjustmentsCapable of adapting to limitless engine and camshaft profiles Available with or without 7? Android Touch screen device with pre-loaded E Tuner AppEFI Electronic fuel injection system Course in Rawalpindi, Islamabad, Pakistan. 03115193625, 3354176949EFI Course Content:Tools Power outputFuel efficiencyEmissions performanceRunning on alternative fuels Reliability Drive ability and smooth operation Initial cost Maintenance cost Diagnostic capabilityRange of environmental operationEngine tuning. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.call 03115193625,03354176949registered recognized, approved and authorized instituteINTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,registered recognized, approved and authorized instituteFor More Information Visit Our Website www.courses.com.pk, www.icollegete.com. EFI Auto Car Theory + Practical Training Course in Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. International college of technical education offers different type of courses and diplomas out of which some are as follows:

Car Scanner Training's Practical Auto EFI Technology Efi Auto electrician Diploma Course (Theory+Practical) in rawalpindi abbottabad haripur murree balakot +923354176949 Car Scanner Training's Practical Auto EFI Technology Efi Auto electrician Diploma Course (Theory+Practical) Worldwide acceptable Diploma in rawalpindi islamabad chakwal gujrat jhelum sargodha 3354176949. Auto electrician in Peshawar Mardan Malakand swat 3115193625 Admission open, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Admission open for admission and queries call 3115193625, 3354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment, An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to controll engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of "electronic control unit", and then specific ECU's were developed. Now, ECU's are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU's and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle. ICTE Auto Electrician Course Content: Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan IATA Air Ticketing & Reservation Course in Islamabad IATA Air Ticketing & Reservation Course in Rawalpindi IATA Air Ticketing & Reservation Course in Pakistan Professional Cooking Course in Islamabad Professional Cooking Course in Rawalpindi Professional Cooking Course in Pakistan EFI Auto Electrician Course in Rawalpindi EFI Auto Electrician Course in Islamabad EFI Auto Electrician Course in Pakistan Civil 3D Course in Islamabad Civil 3D Course in Rawalpindi Civil 3D Course in Pakistan GIS Geographic Information Systems Course in Islamabad GIS Geographic Information Systems Course in Rawalpindi GIS Geographic Information Systems Course in Pakistan Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Admission open for admission and queries call 03115193625,03354176949

Auto EFI Technology Efi auto electrician Diploma Course (Theory+Practical Course) Efi Scanner Training In rawalpindi islamabad gujrat gujarkhan pakistan +923354176949 Auto EFI Technology Efi Auto electrician Diploma Course (Theory+Practical) Worldwide acceptable Diploma in rawalpindi islamabad chakwal gujrat jhelum sargodha 3354176949. Auto electrician in Peshawar Mardan Malakand swat 3115193625 Admission open, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Admission open for admission and queries call 3115193625, 3354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment, An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to controll engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of "electronic control unit", and then specific ECU's were developed. Now, ECU's are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU's and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle. ICTE Auto Electrician Course Content: Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan IATA Air Ticketing & Reservation Course in Islamabad IATA Air Ticketing & Reservation Course in Rawalpindi IATA Air Ticketing & Reservation Course in Pakistan Professional Cooking Course in Islamabad Professional Cooking Course in Rawalpindi Professional Cooking Course in Pakistan EFI Auto Electrician Course in Rawalpindi EFI Auto Electrician Course in Islamabad EFI Auto Electrician Course in Pakistan Civil 3D Course in Islamabad Civil 3D Course in Rawalpindi Civil 3D Course in Pakistan GIS Geographic Information Systems Course in Islamabad GIS Geographic Information Systems Course in Rawalpindi GIS Geographic Information Systems Course in Pakistan Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Admission open for admission and queries call 03115193625,03354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com.

Professional Efi Auto Electrician Courses in Faisalabad Sialkot, Efi Auto Electrician Course in Taxila Wah Rawalpindi, International College Of Technical Education Offer Efi Auto Electrician Course in Taxila Wah Rawalpindi 03115193625, Best Efi Auto Electrician Course in Taxila Wah Rawalpindi 03354176949, Professional Efi Auto Electrician Course in Taxila Wah Rawalpindi 03115193625, Admission open for boys and girls new session started coming soon certification acceptable in Government job and Worldwide UK USA KSA China Japan Canada Saudia Dubai Muscat Oman Bahrain Kuwait Qatar, Lowest fee Efi Auto Electrician Course in Taxila Wah Rawalpindi 03115193625, EFI stands for ELECTRONIC FUEL INJECTION The Electronic Fuel Injection system fitted to most modern vehicles combines sophisticated computer controls with a high pressure fuel delivery system to provide optimum power and fuel efficiency. The system is controlled by an electronic control unit (ECU).What is an auto electrical? Automotive electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment.Which is better EFI or carburetor? EFI systems are more fuel-efficient than carbureted engines. This is because the electronic system constantly adjusts the air to fuel ratio to ensure that optimal levels are delivered. Carbureted engines, on the other hand, may deliver an excess fuel to air ratio, which can lead to more fuel consumption.What is the function of EFI? Your electronic fuel injection (EFI) system delivers fuel to the engine in a high speed and efficient manner, helping your vehicle to run smoothly. Symptoms of an EFI problem include the smell of fuel in the car, idling roughly, problems starting and frequent stalling.Automotive electricians are specialists in the diagnosis and repair of faults in the electrical and electronic components of all types of vehicles. In addition to lighting, starting, charging and ignition systems, the widespread use of on-board computers has given an added dimension to the complexity of an automotive electrician’s work. An Apprenticeship in this vocation is an exciting opportunity to enter the industry.Auto Electrician is there to service, maintain, check up, repair, and change electric and electronic devices and systems on the vehicle. A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions.Also, this tradesman should perform quality control for the electrical work performed, considering the norms and regulations.Within the auto electric trade courses, International College of Technical Education has a six-month auto electrician course to offer. Having finished this course, each student will be able to identify the types and elements of electric installations, and network equipment; to differ the electric symbols, and explain how the electric installations are set up on a vehicle.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan.Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan EFI Auto Electrician Course Contents: Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits

EFI AUTO ELECTRICIAN course in baag muzaffarabadInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment EFI Auto Electrician Course Contents: Tools Special purpose tools Measuring Instruments Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Batteries This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI VEHICLE AUTO ELECTRICIAN course in Abbottabad HaripurInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment his course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI VEHICLE AUTO ELECTRICIAN course in Mardan Charsadda RawalakotInternational college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment his course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/

EFI AUTO ELECTRICIAN course in HANGU KARAK International college Of Technical Education Offer Diploma in information techonogy (DIT) in Rawalpindi Taxila Wah 03115193625 Best Diploma in information techonogy (DIT) in Rawalpindi Islamabad Pakistan professional traning Diploma in information techonogy (DIT) in Rawalpindi Islamabad Taxila Wah 03354176949 Admission open for boys and girls new session started coming soon. EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment EFI Auto Electrician Course Contents: Tools Special purpose tools Measuring Instruments Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Batteries This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician – probably from a role where responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more Module one: Auto Electrician 1. Safety precautions 2. Safe Working Practices in Automotive Workplace 3. Tools used in Auto electrician and EFI work 4. Introduction to Battery & Electrical fundamentals 5. Function, Types and parts of ignition system 6. Purpose and Function of Automobile self-starter 7. Automobile generator design and function 8. Fuel Pump, Fuel Filter and Fuel Lines System 9. Four Cylinder Engine working and power system 10. Head light circuit and indicator circuit system 11. ODO meter, speedo meter and RPM system 12. Fuel Gauge and Temperature Gauge System 13. Scanner working and use system 14. Horn and Air bags system 15. Fuel Engine and Diesel Engine working system 16. Power window and center lock system 17. Function of Plug and its working 18. Function of thermostat in Automobile 19. Water pump and Automatic Fan System 20. Tail and Parking Light System Module Two: EFI System 1. Introduction to EFI Engine system 2. Tools use in EFI system 3. Precautions of working environment of EFI system 4. Difference between Distributor and CDI 5. EFI engine check light system 6. The purpose of Check Engine Light 7. EFI Engine Sensors working operation system 8. Cranking and Cam sensors degree notification in EFI System 9. What is Air Bag system how its work 10. How working of EFI engine fuel injector and its plus 11. Difference between Throttle and carburetor system 12. ABS Breaking System in EFI system 13. EFI Engine Manual Diagnostic System 14. EFI Engine Tuning System 15. Catalytic Convert system in EFI 16. How to control ECU EFI Engine 17. Automatic and Manual Gear system 18. EFI Fuel Pump system 19. Cranking and charging systems Fee=25000 DURATION = 3 MONTH For Registration: 0092-311-5193625 / 0092-335-4176949 http://www.icollegete.com/course/efi-auto-electrician-course … from Jul 1st

Advance EFI Auto car Electrician (theory+practical) professional Course in Rawalpindi jhelum 03115193625, 03354176949, Advance EFI Auto car Electrician (theory+practical) professional Course in Rawalpindi jhelum 03354176949 International college of technical education offers advance diploma in efi auto electrician Advance EFI Auto car Electrician (theory+practical) professional Course in Rawalpindi jhelum n auto electrician is a tradesman specializing in electrical wiring of motor vehicles. Auto electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical components. Auto electricians specialize in cars and commercial vehicles. Auto electricians work in dealer workshops or in independent service centers, diagnosing and repairing a vehicle's electrical faults. As automotive systems increase in complexity and feature more electronic components and accessories, the role of auto electrician becomes more important. Experienced auto electricians might work as independent technicians, offering a specialist service to vehicle owners or service centers, Auto electricians work on all vehicle electrical systems and components, including ignition, fuel injection and engine management systems, anti-lock braking, battery, wiring and charging systems, heating and air conditioning systems, lighting and indicators. They must also be familiar with increasingly-sophisticated in-car entertainment systems, including radios and video players, cell phone, navigation and vehicle information systems. A key role for auto electricians is fault diagnosis. They meet vehicle owners to discuss problems and carry out tests to identify the problem. If a vehicle has starting problems, intermittent running faults or poor fuel consumption, they use specialist skills and tools to diagnose problems in the ignition, fuel injection and engine management systems. To diagnose a vehicle with braking problems that are not due to mechanical faults, auto electricians diagnose the anti-lock braking system. They also test the battery and charging systems to ensure that electrical components are receiving the correct voltage. Auto electricians test vehicle lighting systems to ensure they are operating correctly. They test headlight beam alignment and lighting intensity in line with specifications and make any necessary adjustments. They fit additional lighting components, such as fog lights or emergency lights, ensuring that they are correctly connected to the electrical system. This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician probably from a role where they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working.Complete EFI Auto Electrician theory+practical Course in rawalpindi 3115193625, Efi electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, World Wide Acceptable with UK/USA/Pak/U.A.E/KSA/China/ International Certifications in Rawalpindi,Islamabad, Auto electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, Admission open We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations. Admission open in Complete efi course for admission and queries call 03115193625,03354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. An auto electrician is a tradesman specializing in electrical wiring of motor vehicles. Auto electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical components. Auto electricians specialize in cars and commercial vehicles. Auto electricians work in dealer workshops or in independent service centers, diagnosing and repairing a vehicle's electrical faults. As automotive systems increase in complexity and feature more electronic components and accessories, the role of auto electrician becomes more important. Experienced auto electricians might work as independent technicians, offering a specialist service to vehicle owners or service centers, Auto electricians work on all vehicle electrical systems and components, including ignition, fuel injection and engine management systems, anti-lock braking, battery, wiring and charging systems, heating and air conditioning systems, lighting and indicators. They must also be familiar with increasingly-sophisticated in-car entertainment systems, including radios and video players, cell phone, navigation and vehicle information systems. A key role for auto electricians is fault diagnosis. They meet vehicle owners to discuss problems and carry out tests to identify the problem. If a vehicle has starting problems, intermittent running faults or poor fuel consumption, they use specialist skills and tools to diagnose problems in the ignition, fuel injection and engine management systems. To diagnose a vehicle with braking problems that are not due to mechanical faults, auto electricians diagnose the anti-lock braking system. They also test the battery and charging systems to ensure that electrical components are receiving the correct voltage. Auto electricians test vehicle lighting systems to ensure they are operating correctly. They test headlight beam alignment and lighting intensity in line with specifications and make any necessary adjustments. They fit additional lighting components, such as fog lights or emergency lights, ensuring that they are correctly connected to the electrical system. This course is for learners who want to gain knowledge and basic skills required in the job of an Auto Electrician probably from a role where they work under supervision or independently. The qualifications are for learners who want to increase their skills and take on more responsibility. Units in the qualification cover all areas of working in Auto Electrical Industry/Workshop, customer support. In particular, the learners will have acquired competencies to: • Work effectively as Auto Electrician • Maintain/Service /Repair Lighting System of Vehicles. • Test and Recharge Battery. • Service/ Repair /Test Starting System of Auto Vehicles. • Repair/Service /Test Charging System. • Service/Replace Electrical Accessories. • Maintain Safety during working. Efi Auto Electrician Professional course for admission and queries call 03115193625

EFI Auto Electrician Experience Based Diploma Course In Rawalpindi Shamsabad Murree road For UAE KSA OMAN China Worldwide acceptable Diploma EFI Auto Electrician in Rawalpindi Peshawar Mardan Malakand swat 3115193625 , Auto car Electrician Course in rawalpindi pakistan chakwal jhelum gujrat 03115193625, World Wide Acceptable with UK/USA/ Pak/U.A.E/ KSA/China/ International Certifications in Rawalpindi, Islamabad, Efi Auto Course in rawalpindi pakistan chakwal jhelum gujrat O3115193625, Auto electrician in Peshawar Mardan Malakand swat O3115193625 Admission open, We offers specialized and centralized fully equipped computer lab,various professional lecture rooms with multimedia for audio /video visual aid,Conference hall,hands-on supervisory experience in service and operations, Admission open for admission and queries call O3115193625, O3354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute,For More Information Visit Our Website www.courses.com.pk, www.icollegete.com. Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician course in Rawalpindi, Islamabad, Pakistan. EFI diploma course in Rawalpindi, Islamabad, Pakistan. Electronic fuel injection system course in rawalpindi, islamabad, pakistan. Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment, An electrician is a tradesperson specializing in electrical wiring of buildings, stationary machines, and related equipment. Electricians may be employed in the installation of new electrical components or the maintenance and repair of existing electrical infrastructure. Electricians may also specialize in wiring ships, airplanes, and other mobile platforms, as well as data and cable. Automotive electronics are any electrically-generated systems used in road vehicles, such as: carputers, telematics, in-car entertainment systems, etc. Automotive electronics originated from the need to control engines. The first electronic pieces were used to control engine functions and were referred to as engine control units (ECU). As electronic controls began to be used for more automotive applications, the acronym ECU took on the more general meaning of "electronic control unit", and then specific ECU's were developed. Now, ECU's are modular. Two types include engine control modules (ECM) or transmission control modules (TCM). A modern car may have up to 100 ECU's and a commercial vehicle up to 40. Automobile engineering, along with aerospace engineering and marine engineering, is a branch of vehicle engineering, incorporating elements of mechanical, electrical, electronic, software and safety engineering as applied to the design, manufacture and operation of motorcycles, automobiles and trucks and their respective engineering subsystems. It also includes modification of vehicles. Manufacturing domain deals with the creation and assembling the whole parts of automobiles is also included in it.The automotive engineering field is research -intensive and involves direct application of mathematical models and formulas. The study of automotive engineering is to design, develop, fabricate, and testing vehicles or vehicle components from the concept stage to production stage. Production, development, and manufacturing are the three major functions in this field. Automobile Engineering is mainly divided into three streams such as production or design engineering focuses on design components, testing of parts, co-ordinating tests, and system of a vehicle. ICTE Auto Electrician Course Content: Tools Special purpose tools Measuring tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits. Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawalakot, Bagh, Bahawalpur, Bhakkar, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan. Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.Dubai , Abu Dabi , Muscat , Oman , Doha , Qatar ,South Africa , Saudia Arabia , kawat , Behrain , Kotli Sattian , Murree , UK , UAE , Sharja,Civil Technology Courses Diploma in Civil Surveyor Diploma in Quantity Surveyor Diploma in Civil Draftman Diploma in Civil Lab Technician Diploma in Civil Architecture Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber Diploma in CCTV technician Mechanical Technology Courses Quality Assurance Quality Control Course in peshawar Shorthand Professional Course in Islamabad Shorthand Professional Course in Rawalpindi Shorthand Professional Course in Pakistan IATA Air Ticketing & Reservation Course in Islamabad IATA Air Ticketing & Reservation Course in Rawalpindi IATA Air Ticketing & Reservation Course in Pakistan Professional Cooking Course in Islamabad Professional Cooking Course in Rawalpindi Professional Cooking Course in Pakistan EFI Auto Electrician Course in Rawalpindi EFI Auto Electrician Course in Islamabad EFI Auto Electrician Course in Pakistan Civil 3D Course in Islamabad Civil 3D Course in Rawalpindi Civil 3D Course in Pakistan GIS Geographic Information Systems Course in Islamabad GIS Geographic Information Systems Course in Rawalpindi GIS Geographic Information Systems Course in Pakistan Electronic Fuel Injection (EFI) course in Rawalpindi, Islamabad, Pakistan. EFI electrician Experience based Diploma in Rawalpindi, Islamabad, Pakistan. EFI diploma Experience based Diploma in Rawalpindi, Islamabad, Pakistan. Experience based Electronic fuel injection system Diploma in rawalpindi, islamabad, pakistan. Admission open for admission and queries call 03115193625, 03354176949 INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training Institute, For More Information Visit Our Website www.courses.com.pk, www.icollegete.com.

Auto Car Electrician Course in Bagh Muzaffarabad,Auto Car Electrician Course in Rawalpindi Chakwal,international college of technical education in rawalpindi chakwal,best auto car electrician institute in rawalpindi chakwal punjab pakistan,professional auto car efi electrician training course in rawalpindi chakwal pakistan,practical auto car efi electrician diploma course in rawalpindi chakwal punjab pakistan,lowest fee auto efi car electrician dploma course in rawalpindi punjab pakistan,admission open for boys and girls new session start 15 september 2020 certification acceptable in government job and worldwide Uk usa uae dubai saudia muscat oman kqatar kuwait china,International College of Technical Education.Head Office : Office # 27, Second Floor, Maryam Shadi Hall Plaza (Airies Plaza), Shamsabad, Murree Road, Rawalpindi, Pakistan 0311-5193625, 0092-335-4176949,What is Efi Auto Electrician? EFI Automotive electricians assess vehicles and find faults using diagnostic testing equipment. They also install and repair electrical and electronic equipment this can be in passenger and commercial vehicles to marine, and in mining equipment. Automotive electricians often interact directly with a customer asking for clarification of the problem with their vehicle, and then explaining what needs to be done.Auto Electricians perform work on cars requiring repairs to electronic fuel injection systems. Whether your car is having trouble starting, running rough, hesitating, has poor fuel economy or mileage, or has poor performance you may need to have the Fuel Injection System checked or cleansed and we can help.The fuel injectors (especially the nozzles) operate in an environment where tremendous heat is generated. The burning of fuel leaves hardened carbon deposits on piston valves and the fuel injector nozzle head that reduces the performance of the spray pattern and flow of fuel. A fuel injection service will cleanse the injector nozzles, dissolving the carbon deposits and restore proper fuel spray and flow, improving performance, reliability and fuel economy.We can check, repair or service your car’s electronic fuel injection system, fuel pump, fuel lines, fuel injectors, fuel tank, air flow meter, oxygen sensors and other fuel system components onsite.E.F.I. & Auto Electricians is a locally owned and operated business, servicing Penrith and surrounding areas. We strive to provide high quality service at cost-effective price. From light commercial, all wheel drives, 4WDs, imported cares to Utes and vans, we are able to work on all makes and models. We are your local specialist in motor vehicle auto electrical services and repairs.Auto Electricians install, maintain, identify faults and repair electrical wiring and computer-based equipment in motor vehicles and related equipment, such as caravans, trailers, earthmoving equipment, mining equipment, marine applications and agricultural equipment. Auto Car Electrician Course Content: Monitor Environmental And Sustainability Best Practice In The Automotive Mechanical Industry Apply Safe Working Practices In An Automotive Workplace Use And Maintain Automotive Electrical Test Equipment Carry Out Soldering Of Electrical Wiring And Circuits Demonstrate Knowledge Of Automotive Electrical Circuits And Wiring Systems Install, Test And Repair Vehicle Lighting And Wiring Systems Fabricate, Test And Repair Wiring Harnesses And Looms Test And Repair Basic Electrical Circuits Demonstrate Knowledge Of Petrol And Diesel Engine Operation Diagnose And Repair Electronic Spark Ignition Engine Management Systems Diagnose And Repair Electronic Compression Ignition Engine Management Systems Test, Charge And Replace Batteries Install Ancillary Electronic Control Unit Systems And Components Diagnose And Repair Instruments And Warning Systems Diagnose and repair charging systems Diagnose And Repair Ignition Systems Repair Electrical Systems Service And Repair Electronic Body Management Systems Service And Repair Electronic Drive Management Systems Carry Out Diagnostic Procedures Remove And Replace Supplementary Restraint Systems Tools Special purpose tools Measureing tools Fastening devices and tube fittings Electrical fundamentals Cranking and charging systems Electrical circuits Rawalpindi, Islamabad, Lahore, Karachi, Gilgit, Skardu, Ghangche, taxila, Shigar, Astore, Diamer, Ghizer, Kharmang, Gultari, Rondo, Hunza Nagar, Gupi, Azad Jammu and Kashmir, Muzaffarabad, Mirpur, Bhimber, Kotli, Rawlakot, Bagh, Bahawalpur, Bhakkar, Chakwal, Chiniot, Dera Ghazi Khan, Faisalabad, Gujranwala, Gujrat, Hafizabad, Jhang, Jhelum, Kasur, Khanewal, Khushab, Layyah, Lodharan, Mandi-Bahuddin, Mianwali, Multan, Muzaffargarh, Nankana Sahib, Narowal, Okara, Pakpattan, Rahim Yar Khan, Rajanpur, Sahiwal, Sargodha, Sheikhupura, Sialkot, Toba tek Singh, Vehari, Attock, Taxila, Wah Cantt, Rawalpindi, Balochistan, Khyber-Pakhtunkhwa, Punjab, Sindh, Gilgit Baltistan, Turbat, Sibi, Chaman, Lasbela, Zhob, Gwadar, Nasiraba, Jaffarabad, Hub, Dera Murad Jamali, Dera Allah Yar, Khyber-Pakhtunkhwa, Peshawar, Mardan, Abbottabad, Mingor, Kohat, Bannu, Swabi, Dera Ismail Khan, Charsadda, Nowshera, Mansehra, Hyderabad, Sukkur, Larkana, Nawabshah, Nanak wara, Mirpur Khas, Jacobabad, Shikarpur, Khairpur, Pakistan.Experienced Based Diploma in Ac Technician ,Electronic , Mechanical , Plumbing , Auto Electrician , Efi Auto Electrician , Civil Surveyor , Quantity surveyor civil lab material testing , Best Institute in Rawalpindi islamabad Pakistan Lahore , Lowest fee course in pakistan , lowest fee professional practical training course in pakistan rawalpindi peshawar kashmir bagh lahore islamabad kahuta chakwal rahimyar khan gujarat gujarawala multan , attock Best institute in rawalpindi professional teacher and qualified staff.Dubai , Abu Dabi , Muscat , Oman , Doha , Qatar ,South Africa , Saudia Arabia , kawat , Behrain , Kotli Sattian , Murree , UK , UAE , Sharja,Civil Technology Courses Diploma in Civil Surveyor Diploma in Quantity Surveyor Diploma in Civil Draftman Diploma in Civil Lab Technician Diploma in Civil Architecture Diploma in Civil Engineering One Year Diploma in Civil Engineering Two Years OSHA Construction Civil Safety Electrical Technology Courses Diploma in Electrical Engineering one year Diploma in Electrical Engineering Two years Electrician Course in Rawalpindi Electrician Course in Lahore Electrician Course in Peshawar Telecommunication Technology Courses Diploma in Telecommunication One year Diploma in Telecommunication Two years Diploma in Optical Fiber www.icollegete.com www.courses.com.pk International College of Technical Education. Head Office : Office # 27, Second Floor, Maryam Shadi Hall Plaza (Airies Plaza), Shamsabad, Murree Road, Rawalpindi, Pakistan 0311-5193625, 0092-335-4176949 Auto Car Electrician Course in Bagh Muzaffarabad.

Efi Auto Electrician Course in Peshawar Charsadda,Efi Auto Electrician Course in Rawalpindi Taxila Gujar Khan, International College Of Technical Education Offer Efi Auto Electrician Course in Rawalpindi Taxila Gujar Khan 03115193625, Professional Efi Auto Electrician Course in Rawalpindi Taxila Gujar Khan 03354176949, Best Efi Auto Electrician Course in Rawalpindi Taxila Gujar Khan 03115193625, Lowest fee Efi Auto Electrician Course in Rawalpindi Taxila Gujar Khan, Admission open for admission and queries call 03115193625,03354176949. INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training, Technical, Management and Safety Officer Institute, For More Information Visit Our Website http://www.icollegete.com/ https://courses.com.pk/ Certification acceptable in Government job and Worldwide UK USA KSA UAE Canada Dubai Muscat Oman Bahrain Kuwait Qatar Saudia Japan China, What is auto EFI? EFI stands for ELECTRONIC FUEL INJECTION The Electronic Fuel Injection system fitted to most modern vehicles combines sophisticated computer controls with a high pressure fuel delivery system to provide optimum power and fuel efficiency. The system is controlled by an electronic control unit (ECU).What is the function of EFI? Your electronic fuel injection (EFI) system delivers fuel to the engine in a high speed and efficient manner, helping your vehicle to run smoothly. Symptoms of an EFI problem include the smell of fuel in the car, idling roughly, problems starting and frequent stalling.A good and reliable auto electrician should know how to set up electric installations and network equipment on the cat based on the sketches; how to detect and remove installation and network equipment malfunctions.Also, this tradesman should perform quality control for the electrical work performed, considering the norms and regulations.Within the auto electric trade courses, International College of Technical Education has a six-month auto electrician course to offer. Having finished this course, each student will be able to identify the types and elements of electric installations, and network equipment; to differ the electric symbols, and explain how the electric installations are set up on a vehicle.The school also incorporates introducing the students to the procedures and rules of connecting electric and electronic devices to the installations, as well as to differ the types and uses of the tools, and devices which build and set up the electric installation and network equipment. Apart from theoretical representation of these procedures, the students will also be trained to set up and connect electric and electronic devices on the installations, to check the regularity of the installations, and use the appropriate tools.The auto electrician course in International College of Technical Education offers you the chance to learn about terms such as ECU, and CPU, learn what system sensors are, and explain how they work (coolant fluid temperature sensor, air temperature and flow sensor).In our school you will learn what an encoder is, how it functions, what is Hall effect, what is a “Knock” sensor, and what is the purpose of the sensor for the car speed.This training for auto electrician is the best and the most comprehensive possible offer.It is a reliable and high-quality course to prepare you for this trade, highly in demand.The practice within this training is certainly the most important segment. You can have the practice in a shop that ICTE Institute cooperates with, and it is not included in the course fee. Within the course fee we have included the textbook, the final exams, and a certified diploma. EFI Auto Electrician Course Contents: 1:Tools 2:Special purpose tools 3:Measureing tools 4:Fastening devices and tube fittings 5:Electrical fundamentals 6:Cranking and charging systems 7:Electrical circuits Admission open for admission and queries call 03115193625,03354176949. INTERNATIONAL COLLEGE OF TECHNICAL EDUCATION Pakistan No.1 IT Training, Technical, Management and Safety Officer Institute, For More Information Visit Our Website http://www.icollegete.com/ https://courses.com.pk/ Certification acceptable in Government job and Worldwide UK USA KSA UAE Canada Dubai Muscat Oman Bahrain Kuwait Qatar Saudia Japan China http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi-pakistan/ http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi/ http://www.icollegete.com/course/efi-auto-electrician-course-in-pakistan/ http://www.icollegete.com/course/efi-auto-electrician-course-in-rawalpindi-pakistan/ http://www.icollegete.com/course/electronic-fuel-injection-efi-course-in-pakistan/